一、双组份打胶机的操作说明

　　I. operation instructions of two component gluing machine

　　1.接通电源(380V 三相四线)和气源(0.6-0.7MPa)。

　　1. turn on the power supply (380V three-phase four wire) and air source (0.6-0.7MPa).

　　2.打开A,B胶供胶阀门，关闭B胶回流阀门。

　　2. open A, B glue valve, turn off B glue return valve.

　　3.在控制面板上选择“开机”然后检查一下A,B胶是否工作正常。此时供胶机混胶工作准备就绪，如果长时间不用(超过15分钟)或者是下班时要在控制面板上选择“冲枪”，然后打开B胶回流阀门，关闭B胶供胶阀门.此时供胶机冲枪准备工作就绪。 调整机器的水平度，调节地脚的高度使机身水平。接通电源后先检查各电机的旋转方向是否正确，接通与CL—A—01打胶机的胶管、信号。

　　3. select "boot" on the control panel, and then check "A" and see if the B glue is working properly. This glue mixing machine is ready, if not a long time (more than 15 minutes) or work to select the "red gun" in the control panel, and then open the B glue return valve closed B glue glue valve. This glue machine gun is ready at. Adjust the level of the machine, adjust the height of the foot, so that the fuselage level. After connecting the power supply, check the direction of rotation of the motor is correct, switch on and CL - A - 01 rubber machine hose, signal.

　　二、双组份打胶机结构

　　Two 、 structure of two component gluing machine

　　1、CL-B-01型双组份供胶机主要有A组份提胶泵、B组份提胶泵， A、B胶增压装置，高压柱塞泵，A、B胶泵连接装置，双组分比例调节机构，高压出口分流装置，液压控制系统，气动控制系统及电器控制系统等组成。

　　1, CL-B-01 type two-component glue machine main component A, B component of gel extraction pump rubber pump, A, B glue pressurizing device, high pressure piston pump, A pump, B glue connecting device, double component ratio adjusting mechanism, a high pressure outlet safety shunt device, hydraulic control system, gas composition pneumatic control system and electric control system etc..

　　2、A组份提胶由电动齿轮泵提供，经管道输送油压驱动的A胶高压柱塞泵增压。B组份提胶由气动往复泵提供，经管道输送油压驱动的B组分高压柱塞泵增压。

　　2, A group of rubber extraction by the electric gear pump, pipeline delivery to the hydraulic pressure driven A glue high pressure plunger pump pressurization. B component extraction is provided by pneumatic reciprocating pump and conveyed by pipeline to B component driven by oil pressure.

　　A、B胶的体积比例由双组分比例调节机构调整，然后，同时送入打胶机混合器，混合器由36节以上混合装置组成，双组份胶充分混合后到达涂胶枪，从胶嘴喷出，涂布于中空玻璃的边缘进行封边。胶嘴设有启动快速关闭阀，用以准确控制出胶时间。

　　The volume ratio of A, B glue by the two-component proportion regulating mechanism, and at the same time, into the glue mixer, the mixer is composed of 36 sections above the mixing device, two-component adhesive after mixing to glue gun, glue from the spout, the edge is coated on the insulating glass edge. The rubber nozzle is equipped with a quick start shut-off valve to accurately control the gum release time.

　　3、A、B组份体积比例调节由双组分比例调节机构完成。 A、B组份比例分配比的调节主要靠调节高压泵前端连轩上的滑块，向上调B胶出胶少，向下调B胶出胶多。滑块中心距上端轴中心线16.4cm时，A/B胶的比例为10比1。

　　3, A, B component volume ratio adjustment by a two component proportional adjustment mechanism to complete. The proportion of A and B components is adjusted mainly by adjusting the front of the high-pressure pump, and even on the slider on the porch, up to the B gel, less gum, down B glue, more gum. The ratio of A/B glue is 10 to 1 when the center line of the block is 16.4cm.

　　以上便是双组份打胶机今天的分享，您还满意吗，欢迎关注我们的网站:http://www.jncsjx.com/并且关注我们的产品，我们将为您提供优良的产品，衷心的愿与您建立合作关系。

　　The above is to share the two-component glue machine today, you still satisfied with it, welcome to our website: http://www.jncsjx.com/ and pay attention to our products, we will provide you with excellent products, sincerely wish to establish business relationship with you.