导致中空玻璃密封不严产生漏气的原因有哪些。

　　What are the reasons for the leakage of insulating glass and the leakage of insulating glass?.

　　一、操作问题

　　I. operation problems

　　1、打开气泵开关，电源总开关，控制台开关，在控制台按手动按钮，我们将打胶机胶头让他回位到原点，这是我们要对打胶机的速度进行下调节(一般情况下使用我们设置好的速度即可)，密封不严可能是由于打胶机的打胶速度过快而我们的铝条安装的时候深浅不一所以导致中空玻璃的密封胶在铝条深的地方会出现密封不严的情况。

　　1, the first open air pump switch, power switch, control switch, manual button on the console, we will glue machine glue head let him return to the origin, this is we want to fight the glue machine speed regulation (we use set speed under normal circumstances can not seal), may be the glue machine glue fast and our aluminum strips when installing shades resulting in insulating glass sealant in aluminum deep place will be sealed and lax circumstance.

　　2、然后是混交了，按桶胶按钮，按工作选择按钮，然后按拍胶启动，在按伐开，此时胶头以出胶，等看不见白胶，以混均匀以后按伐关，此时我们就可以进行正常的打胶机工作了。

　　2, then is mixed, according to the first barrel of plastic button, and then press the select button according to the work, take glue start in cutting, the rubber head to glue, such as invisible glue, to mix well after the press cutting off, we can carry out normal atx-ii work at this time.

　　3、打胶之前注意观察打胶机的胶头是否有玻璃参差等异物出现，如果将其掺入密封胶内那么我们的中空玻璃的密封效果肯定就不会有那么好了。

　　3, before playing glue, pay attention to observe the rubber head of the glue machine, whether there is a glass uneven and other foreign bodies appear, if it is incorporated into sealant, then the sealing effect of our insulating glass will certainly not be so good.

　　二、物料问题

　　Two material problems

　　1、出现中空玻璃打胶机生产出来的中空玻璃密封不好的另一大主要原因就是我们的铝条安装过于随意~~~尽管我们的设备无需进行设置可全自动的检测并处理深浅不一的铝条，但是如果差距太大且打胶速度过快的话也是有可能发生中空玻璃密封不严漏气的情况。

　　1, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum strip is installed too freely while our equipment ~ ~ ~ without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.

　　2、胶体本身质量问题，这种情况我们不是没有遇到过，但是这种情况发生的几率非常的小，但是也非常的容易让人忽略的一个问题，所以小编在这里还是有必要同大家说下这个原因。

　　2, the colloid quality problems, this situation we have encountered, but the probability of this happening is very small, a problem but also very easy to ignore, so small in here is necessary for the same people said this reason.

　　3、打胶机的供娇压力如果不够的话也是会出现这个问题的，因为打胶机的胶体完全靠气压来挤出设备并的涂装在中空玻璃的铝条中的。如果压力过小的话也会导致中空玻璃打胶机密封不严

　　3, if the pressure of the glue machine is insufficient, it will also appear this problem, because the glue of the glue machine is completely squeezed out by the air pressure equipment, and the perfect coating is in the aluminum strip of the hollow glass. If the pressure is too small, it will result in sealed glass sealing machine is not strict

　　本文由双组份打胶机友情奉献.更多有关的知识请点击:http://www.jncsjx.com/我们将用的技术.真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This paper consists of two components of atx-ii friendship devotion. More related knowledge: Please click http://www.jncsjx.com/ we will use the most advanced technology. The most sincere attitude, to provide you with the most comprehensive service. More related knowledge and we will continue to offer. Please look forward to.