全自动丁基胶涂布机的常见故障及解决方法

时间:2024-11-13 来源:http://www.jncsjx.com/ 发布人:昌盛机械

  铝框上出现不沾胶现象 :

  Non stick phenomenon on aluminum frame:

  检查胶缸和胶头的温度是否正常,压力是否在设定范围内。

  Check if the temperature of the rubber cylinder and rubber head is normal, and if the pressure is within the set range.

  检查两胶头之间的距离是否过大,确保铝条能够从两个打胶头之间通过。

  Check if the distance between the two glue heads is too large to ensure that the aluminum strip can pass between the two glue heads.

  如果上述情况正常,可能是打胶头内有杂质堵塞出胶眼,需要卸下打胶头,用煤油浸泡并清理干净后再装上。

  If the above situation is normal, it may be due to impurities blocking the glue hole inside the glue head. The glue head needs to be removed, soaked in kerosene, cleaned, and then reinstalled.

  液压系统漏油 :

  Hydraulic system oil leakage:

  设备采用液压系统,所有连接处均由组合垫密封,若发现漏油,应及时更换组合垫。

  The equipment adopts a hydraulic system, and all connections are sealed with composite gaskets. If oil leakage is found, the composite gaskets should be replaced in a timely manner.

  加热系统异常 :

  Abnormal heating system:

  胶头加热和胶缸加热由加热棒和加热盘提供,温控表设定和调整温度。若温度升不高或升高后下降,检查加热棒或加热盘是否损坏,温控表是否正常。

  The heating of the rubber head and the rubber cylinder are provided by heating rods and heating plates, and the temperature is set and adjusted by a temperature control meter. If the temperature does not rise or decreases after rising, check whether the heating rod or heating plate is damaged, and whether the temperature control meter is normal.

  检查加热器热电偶是否损坏,必要时更换。

  Check if the heater thermocouple is damaged and replace it if necessary.

  胶嘴漏胶 :

  Leakage of glue nozzle:

  关闭涂布机,取下漏胶的胶嘴进行清洗,使用清水或其他清洗剂彻底清除内部胶水后重新安装。

  Turn off the coating machine, remove the leaking glue nozzle for cleaning, thoroughly remove the internal glue with water or other cleaning agents, and reinstall.

  如果清洗后仍漏胶,可能是胶嘴损坏,需要更换。

  If the glue still leaks after cleaning, it may be due to damage to the glue nozzle and needs to be replaced.

  调整涂胶压力,确保压力适中,避免过大或过小。

  Adjust the adhesive pressure to ensure it is moderate and avoid being too high or too low.

  检查胶管是否老化或损坏,必要时更换。

  Check if the hose is aging or damaged, and replace it if necessary.

  触摸屏不显示 :

  Touch screen not displaying:

  检查保险丝是否熔断,及时更换。

  Check if the fuse is blown and replace it promptly.

  油缸不退缸或不进缸 :

  The oil cylinder does not retract or enter the cylinder:

  检查油缸内泄情况,必要时维修或更换。

  Check the leakage inside the oil cylinder and repair or replace it if necessary.

  检查增压泵两端机械阀是否卡住,清理或更换。

  Check if the mechanical valves at both ends of the booster pump are stuck, clean or replace them.

  系统压力异常 :

  Abnormal system pressure:

  检查增压泵工作状态,确保油缸到位后增压泵停止工作。

  Check the working status of the booster pump and ensure that the booster pump stops working after the oil cylinder is in place.

  自动状态下的出胶异常 :

  Abnormal glue dispensing in automatic mode:

  检查加热定时设置,确保在自动状态下温度和压力均正常。

  Check the heating timing settings to ensure that the temperature and pressure are normal in automatic mode.

  检查胶嘴间距是否合适,维修或更换。

  Check if the spacing between the rubber nozzles is appropriate, repair or replace them.

  清理气路,确保气路正常工作。

  Clean the air circuit to ensure its normal operation.中空玻璃外合生产线(8)

  建议定期对设备进行维护和检查,及时发现并解决故障,以保证全自动丁基胶涂布机的正常运行和生产质量。

  It is recommended to regularly maintain and inspect the equipment, promptly detect and solve faults, to ensure the normal operation and production quality of the fully automatic butyl rubber coating machine.

  有了上面的小总结,希望对广大客户有所帮助,如果有什么不理解的或者寻求帮助的请点击我们的网站:http://www.jncsjx.com或者来电咨询,我们会尽全力为您解决

  With the above summary, we hope it can be helpful to our customers. If you have any questions or need help, please click on our website: http://www.jncsjx.com Or call us for consultation, we will do our best to solve it for you

联系我们Contact us

  • 咨询热线:0531-85717458 13705446998
  • 公司地址: 山东省德州市齐河安头乡企巢工业园
  • 扫码联系我们:

截屏,微信识别二维码

微信号:13705446998

//