1、下班时需要清理胶头，关闭连线，把旋转开关旋转到清洗和手动状态，按下排胶启动键，再按排胶阀键，这时胶头出胶，打开黑胶减压阀发排压，降下压力后关闭拧紧，待胶头出胶全是白胶后按下排胶阀键，间隔5秒左右再次按下排胶阀键降白胶压力，待压力降到1以下关闭排胶阀。
　　Need to clean the rubber head 1, work, first close the connection, the rotary switch is rotated to the manual cleaning and discharging state, press the start button, then press button when discharging valve, rubber head glue, open the black glue valve pressure drop under pressure after publishing, close to tighten, head is full of glue glue according to the lower glue glue valve key, the interval of about 5 seconds again press the row key drop glue glue valve pressure, the pressure to be below 1 closed discharging valve.
　　2、生产时需要把玻璃里面一张标签撕掉或贴到玻璃的下方，防止光电感应开关感应到误动作损坏胶头。在自动状态时注意不要用手或其他异物遮挡光电开关，有问题时及时按下急停开关或关闭电源。
　　2, in production, we need to tear off a label in the glass or stick it down to the bottom of the glass, so as to prevent the photoelectric induction switch from causing the misaction to damage the glue head. In automatic state, do not use hand or other foreign objects to shield the photoelectric switch, when the problem is in time to press the stop switch or turn off the power.

　　3、打胶时若胶头残余胶较多时需及时清理，清理时注意防止辅助传送伤手，玻璃平整度不好时需要用手辅助玻璃，必须使检测器在两片玻璃之间移动。
　　3, when glue is used, if the residual glue of glue head is more, it should be cleaned up in time. When cleaning, pay attention to safety and prevent auxiliary transmission of injured hand. When glass flatness is not good, hand assist glass must be used, so the detector must move between two pieces of glass.
　　4、每条边的打胶情况可通过工艺里面的向上调整，上部调整，向下调整，底部调整来适当调整，每次调整需保存。
　　4, the glue on each side can be adjusted to the upper part in the process, the upper part should be adjusted, the bottom should be adjusted, and the bottom adjustment should be adjusted properly. Every adjustment should be saved.
　　5、中途需要更换玻璃厚度或绿条厚度时，待生产上次规格玻璃后一张玻璃时关闭连线，打完后一张玻璃进入输出端停下时转到手动状态，进入玻璃厚度界面设置需要的玻璃厚度或绿条厚度，设置完成以后连线自动生产。
　　5, midway need to replace the glass thickness or green strip thickness, close the connection to the last production specifications of glass last piece of glass, finished the last piece of glass to the manual state into the output end stop when the thickness of the glass into the interface settings need glass thickness or green strip thickness, set up after the completion of the automatic production line.
　　6、需要排胶时先关闭连线，待打胶的玻璃打完并移动到输出端以后按下排胶启动按钮，再按排胶阀。这时需要继续生产就需要把设备旋转到手动状态，按下连线按钮，再次转到自动状态，按下自动运行按钮继续生产。
　　6, when the glue needs to be arranged, the wire is closed first, the glass to be hit finish and then moves to the output end to press the boot button and then press the glue valve. At this point, if we need to continue production, we need to turn the equipment to the manual state, press the connection button, turn to the automatic state again, and press the automatic operation button to continue production.
　　本文的精彩内容来自双组份打胶机详细内容请点击我们的网站:http://www.jncsjx.com谢谢您的到来!
　　The wonderful content of this article comes from the detailed content of the double component glue machine, please click on our official website: http://www.jncsjx.com thank you for your arrival!