固化剂系统为全封闭系统，双组份打胶机杜绝了空气的混入，避免固化剂与空气接触而固化(对硅硐胶固化剂)。确保了介质流量的稳定性，提高混合效果。系统还设有管路超载的保护装置，使操作和使用更加。

The curing agent system is a full closed system, which prevents air from mixing and prevents the curing agent from contacting with air. It ensures the stability of medium flow and improves mixing effect. The system is equipped with a safety protection device for overloading the pipeline to make the operation and use more safe.

由于双组份密封胶的固化需要一定时间，因此，已涂了双组份密封胶的玻璃应水平轻轻搬动,A组、B组份胶应保持清洁，严防异物进入胶中。

Since the curing of two-component sealant takes a certain time, therefore, the glass that has been coated with two-component sealant should be moved horizontally, and the A and B components should be kept clean, so as to prevent foreign matter from entering the glue.

基料泵、固化剂泵及比例泵搞压阀口，均采用零泄露特殊合金研磨制造，比例泵设有独特方便的可调式配比机构，大限度地保证双组份胶近乎苛刻的配比要求，满足玻璃幕墙或中空玻璃的比例要求。

Material pump, pump and pump pressure ratio of curing agent engage the valve port, with zero leakage of special alloy grinding manufacturing, proportional pump is installed with an adjustable proportioning mechanism, to ensure maximum two-component adhesive demanding ratio requirements, meet the curtain wall glass and insulating glass proportion.

在连续工作过程中，胶枪每次停止工作时间一般不得超过20分钟，否则，应用A组份胶冲出全部混合胶，直单一的A组份胶从枪口排出为止,高压胶管不得强行挤压、弯曲，防止影响系统正常工作。

In the continuous working process, glue gun each stopped working time is generally not more than 20 minutes, otherwise, the application of A component glue out all mixed glue, until a single component A glue from the muzzle discharge, high pressure hose shall not be forced to prevent extrusion, bending, impact the normal work of the system.

任何因胶体固化所造成的胶枪、管路或整机的故障，一律不在保修范围之内,定期给各泵的加油口加油，应保证油雾器内不断油。

Any gel curing caused by guns, pipes or the whole machine failure, are not within the scope of warranty, and regularly to the pump refueling mouth refueling, should ensure that the oil mist constantly oil.

气动双组份打胶机，该机是国内的双组份涂胶设备，A组份胶泵和固化剂泵分别采用液压和气动系统驱动，并采用无触点电气控制系统，换向灵敏可靠，关健机制部位采用高强度不锈钢经热处理工艺精制而成，使双组份涂胶机的可靠耐用性大提高，确保了设备的优良品质。

Pneumatic two-component glue machine, this machine is a two-component coating equipment leading, the component of A rubber pump and curing agent pump adopt the hydraulic and pneumatic driving system, and adopts a non-contact electric control system, the reversing mechanism is sensitive and reliable, Guan Jian parts are made of high strength stainless steel after heat treatment technics to make a two-component coating machine to improve reliability and durability, ensure the quality of equipment.

本文由双组份打胶机友情奉献.更多有关的知识请点击:http://linshi.jncsjx.com/我们将用的技术.真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This paper consists of two components of atx-ii friendship devotion. More related knowledge: Please click http://linshi.jncsjx.com/ we will use the most advanced technology. The most sincere attitude, to provide you with the most comprehensive service. More related knowledge and we will continue to offer. Please look forward to.