卧式中空玻璃打胶机Y型过滤器的位置在辅料泵出口处，清洗时将端盖拧下，用煤油浸泡，用牙刷类刷子刷干净。安装时将网放在端盖里用手拧到底，再用扳手拧紧。用一组胶洗一次，如无杂质两组胶洗一次，灵活掌握。

　　The horizontal Y filter is located at the outlet of the auxiliary pump. When it is cleaned, the cover is screwed down, kerosene soaked and toothbrush brushes clean. The installation will be placed on the end cover by hand net screwed in the end wrench, tighten. Use a group of glue to wash once, if there is no impurity, two groups of glue is washed once, and master it flexibly.

　　当胶流速变慢或者混胶不均时清洗混合器。将混合器拆下横放在台钳上，夹住两端盖，不要夹到螺丝。用六角扳手松开两端的六条螺丝，打开器体，取出垫片，挡针，混合芯。将各个零件清洗干净。

　　When the flow rate of the gum slows down or the gum is uneven, the mixer is cleaned. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Use six angle wrench to loosen the six screws at both ends, open the body, take out the gasket, stop pin and the mixing core. Clean the parts.

　　端盖不要弄变形，各个平面不要有划伤。混合器一端有凹槽，安装时将其放进有挡针孔的一面，将挡针放入挡针孔，横放在凹槽上。更换好垫片后将端盖对准器体，A对A，P对P，拧上螺丝，拧好后横放在台钳上夹紧，用扳手拧紧下端的四条螺丝，松开台钳，器体旋转300°，夹紧台钳，再拧紧下面四条螺丝。依次拧四五次即可。

　　Do not deform the end cover, do not scratch any flat surface. One end of the mixer has grooves. When it is installed, it is placed into the side of the pinhole, and the retaining pin is put in the pinhole and positioned on the groove. After replacing the gasket, the end cover is aimed at the body, A A, P to P, screw up the screw, screwed up on the clamp, tighten the four screws at the lower end with the wrench, loosened the table clamp, the body rotates 300 degrees, clamp the tongs, and tighten the four screws below. Turn four or five times in turn.

　　清洗时将其拧下，用尖嘴钳拧下小螺母，拔出针体，弹簧。全部清洗干净。针阀出口平面及针帽确保无任何杂质，划伤，变形。

　　When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean up all. The outlet and needle cap of the needle valve ensure no impurities, scratches and deformations.

　　卧式中空玻璃打胶机卧式中空玻璃打胶机卧式中空玻璃打胶机大过滤器的位置在高压表B表右下，拧下回流阀下方胶管，拧下过滤器，将网及网芯取出，弹簧、取出，刷干净，将弹簧小孔套在网芯的凸点上。倒着裝入器体后转过来拧在胶机上。用3-5组洗一次，如无杂质，灵活掌握即可 。

　　Horizontal hollow glass machine glue machine, horizontal hollow glass beating machine, the horizontal hollow glass rubber beating machine is located at the right of the high pressure meter B, underneath the rubber tube under the backflow valve, screw down the filter, remove the net and net core, spring, remove, brush clean, and put the spring hole on the core of the net. Reverse the loader body and turn it on the glue machine. Use 3-5 groups to wash once, if there is no impurity, we can grasp it flexibly.

　　卧式中空玻璃打胶机胶枪的枪口混合器清洗时直接拧下枪口混合器取出混合芯即可。清洗枪柄混合器时，先把枪上的定位螺丝松开，然后拧下枪柄混合器.

　　When the muzzle mixer of the rubber gun is used for cleaning the horizontal hollow glass glue machine, the muzzle mixer is directly screwed down and the mixing core is removed. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer.

　　本文的精彩内容来自双组份打胶机详细内容请点击我们的网站:http://linshi.jncsjx.com谢谢您的到来!

　　The highlights of this article are from two group glue dispenser. Please click on our official website: http://linshi.jncsjx.com, thank you for coming.