中空玻璃双组份打胶机部分毛病剖析及办法
时间:2018-10-25 来源:http://www.jncsjx.com/ 发布人:昌盛机械
中空玻璃双组份打胶机部分毛病剖析及办法
Analysis and measures of some defects of double glazing machine for insulating glass
中空玻璃设备中的双组份打胶机在运用过程中,或许会由于运用不当或是其他原因形成一些毛病。那么设备在呈现毛病时咱们要假如剖析毛病原因,并采纳相应的办法呢?下面小编介绍双组份打胶一些毛病及办法。
During the operation of the two-component glue beater in the hollow glass equipment, there may be some defects due to improper use or other reasons. So when the equipment is defective, do we need to analyze the causes of the defects and adopt corresponding methods? The following is a brief introduction to some problems and solutions of the two components.
1.双组份打胶机A.B组份份额不对
1. the proportion of A.B component of two component glue machine is not right.
呈现这种状况的原因有以下几种状况:
The reasons for this situation are the following:
份额泵阻塞。B泵吸空。A泵或B泵有内走漏。A胶或B胶桶无料。份额泵前有空气未排出。混合器单向阀走漏。B泵过滤器阻塞。
The share pump is blocked. B pump empty. A pump or B pump has internal leakage. A gum or B gum bucket is not available. Air is not discharged before the pump. The mixer one-way valve leaks. B pump filter blocked.
针对以上原因咱们采纳以下办法进行处理:
In view of the above reasons, we adopt the following measures to deal with:
清洗份额泵;B泵压盘放气阀翻开放气;替换A泵或B泵密封圈;加料;翻开份额泵前的放气阀放气;.清洗或替换 混合器单向阀;清洗B泵过滤器。
Cleaning share pump; B pump pressure disc vent valve open air; Replacing A or B pump seal; Feeding; Opening share pump before the vent valve air;. Cleaning or replacing mixer one-way valve; Cleaning B pump filter.
2..当咱们在运用双组份打胶机时挤胶不接连,发作这种状况的原因有以下几种状况:
2. When we use a two-component glue beater, there are several reasons for this situation:
混合器未清洗洁净.并已固化。A组份或B组份无料。胶中含有空气。份额泵前空气未排尽。A泵.B泵有内走漏。吸入阀阀芯内的V型密封圈未压紧。B泵过滤器滤网阻塞。
The mixer is not cleaned and cleaned. A component or B component was not available. Glue contains air. The air is not drained before the pump. A pump.B pump has internal leakage. The V seal ring in the suction valve spool is not pressed. B filter strainer blockage.
相应的办法如下:
The corresponding measures are as follows:
清洗混合器;加料(换桶)排尽空气;翻开份额泵前的球阀排气;替换密封圈;压紧阀芯密封圈;清洗B泵过滤器。
Clean mixer; Fuel (barrel change) exhaust air; Open the ball valve before the share pump exhaust; Replace the sealing ring; Press the valve core sealing ring; Clean the B pump filter.
这两种毛病,还有或许由于操作人员或是设备问题呈现其他毛病。
These two problems may also cause other problems due to operators or equipment problems.
本文由济南昌盛机械http://linshi.jncsjx.com整理,对双组份打胶机感兴趣的朋友可以关注我们,我们将为您提供更多知识.
This article is compiled by Jinan Changsheng Machinery http://linshi.jncsjx.com. Friends interested in the two-component glue beater can pay attention to us, and we will provide you with more knowledge.
- 全自动丁基胶涂布机的常见故障及方法 2024/11/13
- 中空玻璃的主要优缺点 2024/11/12
- 中空玻璃充气机的操作方法 2024/11/07
- 介绍中空玻璃生产线的主要组成部分 2024/10/31
- 热熔胶涂布机的涂布控制系统的作用 2024/10/19
- 铝条丁基胶涂布机主要性能介绍 2024/10/16
- 中空玻璃设备生产线的实用性 2024/10/14
- 浅析中空玻璃丁基胶内溢及改善方法 2024/09/03
- 卧式丁基胶涂布机:浅析中空玻璃丁基胶内溢及改善方法 2024/09/02
- 中空玻璃打胶机的从属分类 2024/08/22