全自动封胶机胶阀滴漏留意要点：
Points for attention of drip leakage of glue valve in automatic dispensing machine:
全自动点胶机胶阀滴漏常常发作于胶阀关毕当前，95%的此种情形是由于运用的针头口径太小所致。
The leakage of rubber valve in automatic dispensing machine often occurs at the moment when the rubber valve is closed. 95% of this situation is due to the small caliber of the needle used.
普通应用控制全自动点胶机混合管长度与控制压杆辨别来决议胶水混合水平和控制胶水通断。混合管的混合方式爲静态混合，由一连串左右旋叶片互相垂直陈列在套管内组成，A、B胶水经过混合管时停止延续的切割与重合爲平均的混合液。混合管出口部可接转接头，方便运用任何口径的针头，以保证出胶量准确。
General application controls the length of mixing pipe of automatic dispensing machine and distinguishes the control pressure bar to determine the mixing level of glue and control the glue on and off. The mixing mode of the mixing pipe is static mixing, consisting of a series of left and right rotating blades arranged vertically in the casing. When A and B glue pass through the mixing pipe, the cutting and coincidence stop and become the average mixing fluid. The outlet part of the mixing pipe can be connected with a adapter to facilitate the use of needles of any caliber to ensure accurate glue output.
针筒放入针筒夹持器后并固定就可以衔接气阀了。将点胶控制器的AIR OUT口经过气管衔接到针筒，并把针筒气阀衔接到点胶控制器的AIRIN。将点胶机的‘点胶’接口经过电缆线衔接到点胶控制器的信号输出接口。脚踏板衔接：把脚踏板衔接到点胶机的‘运转’接口上，以控制点胶机的运转。Z轴电缆衔接：将Z轴的衔接电缆插头与点胶机‘Z轴’衔接。
The needle barrel is put into the needle holder and fixed to connect the air valve. The AIR OUT port of the dispensing controller is connected to the needle barrel through the trachea, and the needle air valve is connected to the AIRIN of the dispensing controller. The `dispensing'interface of dispensing machine is connected to the signal output interface of dispensing controller through cable. Foot pedal connection: Connect the foot pedal to the `running'interface of dispensing machine to control the operation of dispensing machine. Z-Axis Cable Connection: Connect the Z-Axis cable plug with the Z-Axis of dispensing machine.

太小的针头会影响液体的活动形成背压， 后果招致胶阀关毕后不久构成滴漏的景象。过小的针头也会影响胶阀开端运用时的排气泡举措，只需改换较大的针头即可处理这种成绩。
Too small needles can affect the activity of the liquid to form back pressure, resulting in a drip phenomenon shortly after the closure of the glue valve. Too small needles can also affect the action of exhaust bubbles when rubber valves are used at the beginning. Only changing larger needles can deal with this kind of performance.
锥形斜式针头发生的背压少，液体活动顺畅。
The conical oblique needle has the least back pressure and the smoothest liquid movement.
液体内空气在胶阀关毕后会发生滴漏景象, 好是事后扫除液体内空气, 或改用不容易含气泡的胶.或先将胶离心脱泡后在运用.霎时胶( 快干胶 ) 在胶阀接头及管路上梗塞此种情形次要因过多的湿气或反复运用过的霎时胶. 应确保运用新颖的霎时胶. 将管路以未含湿气的Aceton丙酮彻底清洗过. 运用的空气应确定完枯燥且于厂内空压与胶阀零碎间加装过滤器. ( 以上办法如依然有效, 则应运用氮气. )
The air in the liquid will drip and leak after the rubber valve closes. It is better to sweep the air in the liquid afterwards, or change to a gel that is not easy to contain bubbles. Or to centrifuge the gel to defoam and then use it. The case of instant glue (quick-drying glue) blocking in the joint of the rubber valve and the pipeline is secondary to excessive moisture or repeated use of instant glue. It is necessary to ensure the use of novel instant glue. The pipeline will be free of moisture. Ceton acetone has been thoroughly cleaned. The air used should be determined to be dull and filters should be installed between the air pressure in the plant and the rubber valve fragments. (If the above methods are still effective, nitrogen should be used.)
需求留意的是，将手持式编程器经过串口线选择到点胶机左侧的接口上。6.如所用点胶控制器同点胶机的衔接器型号相反，可以依据衔接器的芯数不同来看出点胶机的‘点胶’和‘运转’等衔接口，二芯点胶，三芯运转。
It is important to note that the hand-held programmer is selected to the left side of the dispenser through the serial port line. 6. If the dispensing controller used is contrary to the connector type of dispensing machine, we can see the connection interfaces of dispensing machine such as dispensing and running, two-core dispensing and three-core operation according to the different number of connectors.
综上所述有济南昌盛机械提供，想了解更多全自动封胶机知识，欢迎关注我们的网站：http://linshi.jncsjx.com谢谢支持！
In summary, all the above-mentioned Jinan Changsheng Machinery provides, want to know more about automatic sealing machine knowledge, welcome to pay attention to our website: http://linshi.jncsjx.com Thank you for your support!