一准备工作

Preparation work

开启总电源；

Turn on the main power supply;

水箱注满谁，每班生产前30分钟开启水加热器；

Who fills the water tank? Turn on the water heater 30 minutes before each production shift;

开启传送加热检查灯风机毛刷水泵。

Turn on the transmission heating inspection light, fan, brush, and water pump.

二操作步骤

Two operational steps

将玻璃放入清洗机进料段，手推玻璃进入清洗段，玻璃经清洗干燥到出料段；

Put the glass into the feeding section of the cleaning machine, manually push the glass into the cleaning section, and the glass is cleaned and dried to the discharge section;

在出料段检查玻璃清洗质量；

Check the quality of glass cleaning in the discharge section;

玻璃进入覆片机，到达终点接近开关时，玻璃自动停在定位柱处；

When the glass enters the laminating machine and reaches the endpoint close to the switch, the glass automatically stops at the positioning column;

覆片机末端设有脚踏电开关，踩脚踏开关，铝框定位移出，将打好胶的铝框定位安放，再次踩脚踏开关，铝框定位缩回；

The end of the laminating machine is equipped with a foot switch. When the foot switch is pressed, the aluminum frame is positioned and moved out. The glued aluminum frame is positioned and placed. When the foot switch is pressed again, the aluminum frame is positioned and retracted;

与上步骤同时，第二片玻璃经清洗干燥后，已经自动停在清洗机出料段末端的接近开关处待用；

At the same time as the previous step, the second piece of glass has been cleaned and dried, and has automatically stopped at the proximity switch at the end of the discharge section of the cleaning machine for use;

将第二片玻璃人工移到覆片机，与第一篇玻璃合片；

Manually move the second piece of glass to the laminating machine and merge it with the first piece of glass;

按辊压合片机启动按钮，合好片的玻璃自动进入辊压合片机，经辊压，玻璃达到预定厚度尺寸；

Press the start button of the roller lamination machine, and the glass that has been laminated will automatically enter the roller lamination machine. After rolling, the glass reaches the predetermined thickness size;

合好片的玻璃进入翻转台，自动停在翻转台末端，踩脚踏开关2，台面放出平料。

The closed glass enters the flipping table and automatically stops at the end of the flipping table. Step on foot switch 2 and the flat material is released from the table.

三每班结束时，关闭控制台上各按钮，再关总电源。

At the end of each shift, turn off all buttons on the control panel and then turn off the main power.

四注意事项

Four Precautions

玻璃在清洗前必须经过磨边，否则会对部分构件造成损伤。

Glass must undergo edge grinding before cleaning, otherwise it may cause damage to some components.

向水箱及软化水装置注水的自来水开关保持开启且水量充足。

The tap water switch for filling the water tank and softening water device remains open and the water volume is sufficient.

根据实际情况调节电器箱内的水温控制器来设定水温，一般在15度至50度之间，亦可加中性洗涤剂，以达到佳清洗效果。

Adjust the water temperature controller inside the electrical box according to the actual situation to set the water temperature, generally between 15 ° C and 50 ° C. Neutral detergent can also be added to achieve optimal cleaning effect.

调节无级变速器调速按钮，根据玻璃污垢情况调定传送速度（通常3m\min左右）

Adjust the speed control button of the continuously variable transmission and adjust the transmission speed according to the situation of glass dirt (usually around 3m/min)

清洗玻璃厚度为3~12mm，经干燥后玻璃后边缘有微量水珠。

The thickness of the cleaned glass is 3-12mm, and after drying, there are trace water droplets on the edge of the glass.

人和物不能置于翻转台的翻转区域内，以保证安全。

People and objects cannot be placed in the flipping area of the flipping platform to ensure safety.

安装调整完后，请按照操作说明顺序试车，若因调整不好而引起玻璃破裂，须迅速急停，传送反转倒出碎玻璃，并清理干净，以免划伤毛刷及传送辊。

After installation and adjustment, please follow the operating instructions for a test run. If the glass breaks due to poor adjustment, it must be quickly stopped, the conveyor reversed and the broken glass poured out, and cleaned to avoid scratching the brush and conveyor roller.

机器各部分接地良好。

All parts of the machine are well grounded.