1、双组份打胶机设备应装置在干燥、无粉尘、无腐蚀性气体的坏境中（该要求与其他设备一致，当然如果条件达不到至少争夺无腐蚀性气体，毕竟设备中有电线以及管路这些配件抗腐蚀性不高）。
1. Dual-component glue beater equipment should be installed in the dry, dust-free, non-corrosive gas environment (this requirement is consistent with other equipment, of course, if the conditions can not reach at least fight for non-corrosive gas, after all, the equipment has wires and pipelines these parts of the corrosion resistance is not high).
2、室内温度好操控在10～40度的室内坚固地上上，地上应水平度要好。
2, indoor temperature is best controlled in a 10~40 degree indoor firmness on the ground, the level should be better.
3、双组份打胶机装置之前，应先检查是否有因运送、搬动形成的变形、损坏和紧固件松动状况，之前就曾经有客户在移动打胶机的过程中把设备的智能操控系统的一个零部件碰掉了而导致设备无法正常运转，咱们的作业人员到现场后才排查出的原因。
3. Before the two-component glue beater, we should check if there is any deformation, damage and fastener loosening caused by transportation and moving. Before that, a customer knocked off a part of the intelligent control system of the equipment in the process of moving the glue beater, and the equipment could not work properly. Our operators arrived. After the scene, the reasons for the investigation were found out.

4、咱们能够依据地上平坦度的实际状况来经过调整设备的可升降地脚螺栓来调整设备的水平度直到设备水平而安定。然后按图接线并牢靠接地，把气源接入机器所配带的气源接口，保证无漏气现象。
4. First of all, we can adjust the level of the equipment by adjusting the liftable anchor bolts according to the actual situation of the ground flatness until the level of the equipment is stable. Then according to the diagram wiring and firmly grounded, the air source into the machine with the air source interface, to ensure no leakage.
5、向油槽中加注液压油至指定位置，46#液压油（约为50升左右）。
5, fill the tank with hydraulic oil to the specified position, 46# hydraulic oil (about 50 litres).
6、接通电源并打开检查设备是否能够正常运转。
6, turn on the power and turn on the checking equipment.
7.作业原理：压缩空气送入胶瓶（注射器），将胶压进与活塞室相连的进给管中，当活塞处于上冲程时，活塞室中填满胶，当活塞向下推动滴胶针头时，胶从针嘴压出。滴出的胶量由活塞下冲的间隔决议，能够手工调理，也能够在软件中操控。
7. Operating Principle: Compressed air is fed into a rubber bottle (syringe), and the glue is pressed into a feed pipe connected with the piston chamber. When the piston is in the up stroke, the piston chamber is filled with glue. When the piston pushes down the dropping needle, the glue is pressed out of the nozzle. The amount of glue drops can be manually adjusted by the interval of piston undershoot, and it can also be manipulated in software.
8.特色：高速度、对胶剂粘度的低灵敏度。优势：可提高点胶速度，改进点胶环境，提高点胶质量。经过使用气压和以微处理器为根底的定时装置来调理涂敷到部件上的流体量，代替了操作员的人为猜想。
8. features: high speed, low sensitivity to glue viscosity. Advantages: it can improve dispensing speed, improve dispensing environment and improve dispensing quality. Instead of the operator's guess, the amount of fluids coated on the parts is adjusted by using air pressure and a microprocessor-based timing device.

（文章由双组份打胶机编写，更多精彩内容，欢迎重视 http://www.jncsjx.com）
(the article is written by two group glue machine, more exciting content. Welcome to http://www.jncsjx.com).