全自动丁基胶涂布机的操作规程主要包括开机前的检查和开机后的操作步骤，以下是详细的操作规程：

　　The operating procedures of the fully automatic butyl rubber coating machine mainly include pre startup inspection and post startup operation steps. The following are detailed operating procedures:

　　开机前检查

　　Check before startup

　　确保电源安全可靠，气源压力符合要求（0.6-0.8Mpa）。

　　Ensure the safety and reliability of the power supply, and ensure that the gas source pressure meets the requirements (0.6-0.8Mpa).

　　检查电、气路是否正常，各按键是否正常。

　　Check if the electrical and pneumatic circuits are normal, and if all buttons are functioning properly.

　　开机操作步骤

　　Power on operation steps

　　接通电源、气源。

　　Connect the power and gas sources.

　　将油缸升降开关调至中位，启动液压站。液压站启动稳定后，将油缸升降开关转至“升”位置，使胶缸活塞提起，离开胶缸，返至最高位置（此动作必须在胶缸加热到需要的温度后进行）。

　　Adjust the oil cylinder lifting switch to the center position and start the hydraulic station. After the hydraulic station is started and stabilized, turn the oil cylinder lifting switch to the "up" position to lift the rubber cylinder piston, leave the rubber cylinder, and return to the highest position (this action must be performed after the rubber cylinder is heated to the required temperature).

　　将气源总开关旋至“通”位置（或向上拉出），然后向上拉动摆动操作手拉阀，摆缸气缸将胶缸活塞向后摆动，让开胶缸口可投入胶锭。完成后，推回摆缸气阀，并关闭气源总开关。

　　Turn the main switch of the gas source to the "on" position (or pull it up), then pull the swing operation manual valve upwards. The swing cylinder will swing the rubber cylinder piston backwards, allowing the rubber cylinder port to be opened and the rubber ingot to be inserted. After completion, push back the swing cylinder valve and turn off the main air source switch.

　　将胶缸活塞对准胶缸中心，打开胶缸压力开关，使活塞慢慢下压进行入胶。

　　Align the rubber cylinder piston with the center of the rubber cylinder, turn on the pressure switch of the rubber cylinder, and slowly press the piston down to enter the rubber.

　　调整挤胶头间距（6-16mm），并确保间隔框（条）与小压轮、挤胶嘴中心对中性。

　　Adjust the spacing between the extrusion heads (6-16mm) and ensure that the spacing frame (strip) is aligned with the center of the small pressure wheel and extrusion nozzle.

　　启动传送带，开启加热开关、油压开关、胶缸活塞开关。

　　Start the conveyor belt, turn on the heating switch, oil pressure switch, and rubber cylinder piston switch.

　　调整压喷定时器、停喷定时器、停压定时器。

　　Adjust the spray timer, stop spray timer, and stop pressure timer.

　　将间隔框（条）置于传送带上，并用手压着间隔框（条）随传送带前进，保证完全压附在传送带上。

　　Place the spacer frame (strip) on the conveyor belt and press it with your hand to move forward with the conveyor belt, ensuring complete adhesion to the conveyor belt.

　　关机操作步骤

　　Shutdown operation steps

　　作业完毕后，首先关掉温控开关、胶缸活塞开关、油泵开关。

　　After completing the homework, first turn off the temperature control switch, rubber cylinder piston switch, and oil pump switch.

　　关掉传送带开关。

　　Turn off the conveyor belt switch.

　　关掉气源和总电源。

　　Turn off the gas source and main power supply.

　　工艺要求

　　technological requirements

　　调整传送带速度（一般为4—17m/min）。

　　Adjust the conveyor belt speed (usually 4-17m/min).

　　设定挤胶座温度（一般为120℃±25℃），设定胶缸温度（一般为120℃±25℃）。

　　Set the extrusion seat temperature (usually 120 ℃± 25 ℃) and the glue cylinder temperature (usually 120 ℃± 25 ℃).

　　根据加工单要求调整挤头间距，并确保间隔框与小压轮、挤胶嘴中心对中性。

　　Adjust the spacing between the extrusion heads according to the processing order requirements, and ensure that the spacing frame is aligned with the center of the small pressure wheel and extrusion nozzle.

　　注意事项

　　matters needing attention

　　胶未加热到需要温度，不得启动液压站。

　　Do not start the hydraulic station until the glue has been heated to the required temperature.

　　严禁主传动停下时调整速度。

　　It is strictly prohibited to adjust the speed when the main transmission is stopped.

　　温度未降到40℃以下，严禁停止传送系统。

　　It is strictly prohibited to stop the conveying system if the temperature has not dropped below 40 ℃.

　　遇到停电或紧急情况，使用木棒将传送带与挤胶座隔开。

　　In case of power outage or emergency, use wooden sticks to separate the conveyor belt from the extrusion seat.

　　请严格按照上述操作规程进行操作，以确保设备正常运行及人身安全

　　Please strictly follow the above operating procedures to ensure the normal operation of the equipment and personal safety

　　本文由  全自动丁基胶涂布机  友情奉献.更多有关的知识请点击   http://www.jncsjx.com   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from the fully automatic butyl rubber coating machine For more related knowledge, please click http://www.jncsjx.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.