调整双组份打胶机的滴胶量主要涉及以下几个步骤：

Adjusting the dispensing amount of the two-component glue machine mainly involves the following steps:

调整比例泵：双组份打胶机的比例泵负责控制A、B两种胶水的混合比例。通过松开比例杠杆上的比例泵锁紧螺钉，将比例泵内外调整至所需的比例。只有当A胶和B胶的配比达到正常值时，才可进行下面的操作。

Adjust the proportion pump: The proportion pump of the two-component gluing machine is responsible for controlling the mixing ratio of adhesive A and B. Adjust the inside and outside of the proportional pump to the desired ratio by loosening the proportional pump locking screw on the proportional lever. The following operation can only be carried out when the ratio of A glue and B glue reaches the normal value.

调整出胶量：出胶量可以通过气源处理器控制，逆时针调节，出胶量增加，顺时针调节出胶量减小。这里指总出胶量。

Adjust the glue output: The glue output can be controlled by the air source processor. If adjusted counterclockwise, the glue output will increase, and if adjusted clockwise, the glue output will decrease. This refers to the total adhesive output.

调整供胶时间：供液时间可以通过控制器进行调整，范围从0.001-99.99秒可调，以此来控制滴胶量。

Adjust the glue supply time: The liquid supply time can be adjusted through the controller, ranging from 0.001-99.99 seconds, to control the amount of glue dispensed.

检查和调整压力桶输出气压：通过调节两个压力桶的输出气压，可以方便地调节各种不同比例的混合胶水，范围可在1:1至3:1的比例。

Check and adjust the output air pressure of the pressure drum: By adjusting the output air pressure of two pressure drums, it is easy to adjust various proportions of mixed glue, ranging from 1:1 to 3:1.

调整点胶阀气缸行程：通过调节点胶阀气缸的不同行程，可以调节滴胶量。

Adjust the stroke of the dispensing valve cylinder: By adjusting the different strokes of the dispensing valve cylinder, the dispensing amount can be adjusted.

设置“行走开始延时”与“出胶延时”：这两个参数是控制打胶开的胶量的，当之间的差值越大时，打胶开始的胶量越多，反之胶量少，需根据实际需要做适当的调整。

Set "walking start delay" and "dispensing delay": These two parameters are used to control the amount of glue applied. The larger the difference between them, the more glue is applied at the beginning of the dispensing process. Conversely, if the difference is less, appropriate adjustments should be made according to actual needs.

检查和调整混合螺旋管胶嘴：更换或调整混合螺旋管胶嘴，以适应不同的滴胶量需求。

Check and adjust the mixing spiral tube nozzle: Replace or adjust the mixing spiral tube nozzle to meet different dispensing requirements.

检查和调整挂环和胶管：确保挂环无变型，无缺失，胶管无破损，胶管接头螺丝无松动，无硅胶溢出，必要时通知设备人员解决。

Check and adjust the hanging ring and hose: Ensure that the hanging ring is not deformed or missing, the hose is not damaged, the hose joint screws are not loose, and there is no silicone overflow. If necessary, notify the equipment personnel to solve the problem.

以上步骤可以帮助您调整双组份打胶机的滴胶量，以满足具体的生产需求。在进行调整时，请确保遵循设备的操作手册和安全指南，以保证操作的准确性和安全性。

The above steps can help you adjust the dispensing amount of the two-component glue machine to meet specific production needs. When making adjustments, please ensure to follow the equipment's operating manual and safety guidelines to ensure accuracy and safety of the operation.

本文由双组份打胶机为您提供，我们的网站 http://www.jncsjx.com我们将以全心全意的热情为您提供服务，欢迎您的访问！

This article is provided by a two-component glue machine on our website http://www.jncsjx.com We will provide you with wholehearted enthusiasm and welcome your visit!