1、停电时马上到机器后边交流正在运用的排胶阀气管后，手动按动白胶电磁阀使气泵上下运动排胶到全白胶时中止。气管接回原处，完毕。
1. When the power is cut off, immediately go to the back of the machine to exchange the drain valve air pipe being used, then manually press the white glue solenoid valve to make the air pump move up and down to drain glue to stop when it is all white glue. The trachea is back to its original location.
2、出产时需求把玻璃里边一张标签撕掉或贴到玻璃的下方，防止光电感应开关感应到误动作损坏胶头。在主动状况时留意不要用手或其他异物遮挡光电开关，有问题时及时按下急停开关或封闭电源。
2. When producing, a label inside the glass should be torn off or pasted to the bottom of the glass to prevent the photoelectric induction switch from causing damage to the glue head. Be careful not to shield the photoelectric switch with hand or other foreign body when in active condition. Press the emergency shutdown switch or close the power supply when there is a problem.
3、下班时需求整理胶头，首要封闭连线，把旋转开关旋转到清洗和手动状况，按下排胶发动键，再按排胶阀键，这时胶头出胶，翻开黑胶减压阀发排压，降下压力后封闭拧紧，待胶头出胶全是白胶后按下排胶阀键，距离5秒左右再次按下排胶阀键降白胶压力，待压力降到1以下封闭排胶阀。《双系统》留意：泄黑胶压力时有必要把两组黑胶压力都泄完。
3. Need to tidy up the rubber head when off-duty, the first closed connection, the rotary switch to the cleaning and manual conditions, press the glue discharge start key, and then press the glue discharge valve key, when the glue head glue, open the black glue pressure relief valve hair discharge pressure, pressure reduction after sealing tighten, until the glue head is all white glue after pressing the glue discharge valve key, the distance of about 5 seconds Press the rubber drain button again to reduce the pressure of the white glue and close the rubber drain valve until the pressure drops below 1. Double system notice: it is necessary to release two groups of black rubber pressure when discharging black gum pressure.

4、每条边的打胶状况可通过工艺里边的向上调整，上部调整，向下调整，底部调整来恰当调整，每次调整需保存。
4. The gluing condition of each edge can be properly adjusted by the up adjustment, the upper adjustment, the down adjustment and the bottom adjustment in the process. Each adjustment needs to be preserved.
5、半途需求替换玻璃厚度或绿条厚度时，待出产前次规格玻璃终一张玻璃时封闭连线，打完终一张玻璃进入输出端停下时转到手动状况，进入玻璃厚度界面设置需求的玻璃厚度或绿条厚度，设置完结今后连线主动出产。
5. When the glass thickness or green strip thickness is needed to be replaced halfway, the final glass of the previous specification will be closed when the connection is finished. When the final glass enters the output terminal and stops, it will change to manual condition. When the glass thickness interface is set, the required glass thickness or green strip thickness will be set. After the connection is finished, the production will be initiated.
6、需求排胶时先封闭连线，待打胶的玻璃打完并移动到输出端今后按下排胶发动按钮，再按排胶阀。这时需求持续出产就需求把设备旋转到手动状况，按下连线按钮，再次转到主动状况，按下主动运行按钮持续出产。
6. Close the connection before discharging glue, press the discharging button and then the discharging valve when the glass is finished and moved to the output end. At this time the demand for continuous production on the need to rotate the equipment to manual status, press the connection button, again to the active status, press the active operation button to continue production.
7、打胶时若胶头剩余胶较多时需及时整理，整理时留意防止辅佐传送伤手，玻璃平整度欠好时需求用手辅佐玻璃，有必要使检测器在两片玻璃之间移动。
7. When gluing, if there is more glue left in the head, it is necessary to tidy it up in time. When tidying, it is necessary to pay attention to the safety of assistant transmission of injured hands. When glass flatness is not good, it is necessary to use hand-assisted glass to make the detector move between two pieces of glass.
(济南昌盛机械,对双组份打胶机感兴趣的朋友可以关注我们http://linshi.jncsjx.com，敬请期待更多精彩内容，谢谢!）
(Jinan Changsheng Machinery, the two-component glue beater interested in friends can pay attention to our http://linshi.jncsjx.com, please look forward to more exciting content, thank you!