翻开气泵开关，电源总开关，控制台开关，在控制台按手动按钮，然后在显现屏上找到原点设定，点击辅助原点设定，然后点击头部原点设定，留意原点设定时防止头部和辅助吸盘碰撞。等设定好然后返回找到玻璃厚度设定，先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度，输入完以后，点击设置进入。等命令位置和当前位置数值分歧即可，留意设置时传送带上不要有玻璃。
First turn on the air pump switch, power supply switch, console switch, press the manual button in the console, then find the origin setting on the display screen, click on the auxiliary origin setting, then click on the origin setting of the head, pay attention to the origin setting to prevent the head and auxiliary sucker collision. After setting, return to find the glass thickness setting, first the glass thickness, then the aluminium partition, then the glass thickness. After input, click Settings to enter. Just wait for the command position and the current position to diverge. Be careful not to have glass on the conveyor belt when setting.
然后是混交了，按桶胶按钮，按工作选择按钮，然后按拍胶启动，在按伐开，此时胶头以出胶，等看不见白胶，以混平均以后按伐关，在按链接消费线，自动，自动运转，此时能够自动打胶。
Then mix, press the first bucket of glue button, press the work selection button, then press the tap glue to start, in the cut, at this time the glue head to glue, etc. can not see the white glue, after mixing average, press the cut off, in the link consumption line, automatic, automatic operation, at this time can automatically glue.
开端打胶要看每条边每个角打胶能否平均，下面说下如何调整打胶机，在屏幕上点击返回找到密封配方，点击进入，会显现当前密封压力，假如每条边都缺胶，那么可增加压力，压力大胶量大，压力小胶量就小。
Start gluing depends on the average gluing at each corner of each side. Here is how to adjust the gluing machine. Click back on the screen to find the sealing formula. Click in, it will show the current sealing pressure. If there is a lack of glue on each side, it can increase the pressure. Large amount of pressure glue, small amount of pressure glue.

下面说下针对某条边，或某个交，胶量不够的调试办法。在点击密封配方进入后会显现有向上密封，上部密封，向下密封，和下部密封，开端打胶的那条边就是向上密封，然后次第从上。
The following is the debugging method for a certain edge, or a certain intersection, the glue content is insufficient. After clicking on the sealant formula, there will be upward seals, upper seals, downward seals, and downward seals. The first side of the sealant is upward seals, and then from the top.
假如先打胶的这条边，打胶不平均，那么点击向上密封，进入后显现。扫描器开后发开的时间，就是在胶嘴贴到玻璃开端挪动胶嘴出胶的时间，时间长出胶晚，时间短出胶早，扫描器开后开端挪动的时间，就是胶嘴挪动的速度，时间长挪动慢，出胶多，时间短挪动快出胶少
If the edge of the first gluing is uneven, then click on the upward seal and appear after entering. The opening time of the scanner is the time when the glue nozzle is moved from the glue nozzle to the beginning of the glass. The longer the glue nozzle is, the earlier the glue is. The time when the scanner starts moving after the opening of the scanner is the speed of the glue nozzle moving. The longer the time is, the slower the glue is moved, the more the glue is released, and the shorter the time the faster the glue is moved, the faster the glue is released.
扫描胶量细微调整，就是只要某条边胶少，或多，时调整扫描胶量细微调整，数值大胶量就大，数值小胶量就小。然后说下到末端伐关的间隔，数值大，胶嘴到末端胶量少，数值小胶量大。拐角时伐开的时间，就是控制拐角的胶量，数值大胶量大，数值小胶量小。假如拐角胶多就调小数值，拐角胶少，数值加大
Fine adjustment of scanning glue quantity means that as long as a certain edge glue is less or more, fine adjustment of scanning glue quantity will result in large value glue quantity and small value glue quantity. Then, the interval from the end to the end of the cut-off is large, the glue amount from the nozzle to the end is small, and the glue amount from the end is large. The cutting time at the corner is to control the glue quantity at the corner. The value is large, the value is small and the glue quantity is large. If there is more corner glue, the value will be reduced. If there is less corner glue, the value will be increased.
感谢您的阅读与观看，更多关于中空玻璃打胶的详情，欢迎关注我们的官网：http://linshi.jncsjx.com，我们会有更多的精彩内容继续为您呈现，谢谢大家的支持！
Thank you for your reading and watching. More details about gluing hollow glass. Welcome to our official website: http://linshi.jncsjx.com. We will have more wonderful content to continue to show you. Thank you for your support!