放在一个平整干净的平面上，连接电源和气源，两者确认接通之后就开始进行操作。打开气泵开关，电源总开关，控制台开关，在控制台按手动按钮，然后在显示屏上找到原点设定，点击辅助原点设定，然后点击头部原点设定，注意原点设定时避免头部和辅助吸盘碰撞。等设定好然后返回找到玻璃厚度设定，先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度，输入完以后，点击设置进入。
Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected. First turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer, and then the glass thickness. After entering, click the setting to enter.
等命令位置和当前位置数值一致即可，注意设置时传送带上不要有玻璃。然后是混交了，按第一桶胶按钮，按工作选择按钮，然后按拍胶启动，在按伐开，此时胶头以出胶，等看不见白胶，以混均匀以后按伐关，在按链接生产线，自动，自动运行，此时可以自动打胶。
Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting. Then it is mixed. Press the first bucket of glue button, press the work selection button, and then press the glue shooting button to start. Press the cutting open. At this time, the glue head will release the glue. When the white glue is not visible, press the cutting off after mixing evenly. Press the link production line to run automatically and automatically. At this time, the glue can be applied automatically.

调试的注意事项：
Precautions for commissioning:
1、 在当天机器操作完毕后要把胶管内的胶冲出，防止硬化；如果长时间不实用要注意用煤油清洗胶管和胶枪。
1. After the operation of the machine on the same day, the rubber in the rubber hose shall be washed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the hose and gun with kerosene.
2、 双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高，低质量的胶容易堵塞胶管的过滤系统，造成出胶不畅或不均匀。
2. For the silicone glue or polysulfide glue used in the two-component gluing machine, attention shall be paid to that the impurities shall not be too high. The low-quality glue is easy to block the filtering system of the hose, resulting in poor or uneven glue delivery.
3、 在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净，好清洗，因为不同品种甚至的胶容易反应堵塞机器。
3. When changing the type of glue, pay special attention to flush the residual glue in the two-component gluing machine, and it is best to clean it, because the glue of different types and even brands is easy to react and block the machine.
液压站系统的压力，不能调的太高，要根据室内环境温度等实际情况，调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪，否则B组份管路压力将升得很高，造成安全事故。
The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as indoor ambient temperature, adjust it to meet the normal glue output of the glue nozzle and apply glue evenly. When opening the hydraulic station, be sure to open the glue gun, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
本文由双组份打胶机整理发布，您是不是对这些内容有所了解了呢?更多的内容请点击：http://linshi.jncsjx.com我们会有更多精彩内容等你查看。
This article is compiled and released by two-component gluing machine. Do you know something about these contents? For more information, please click: http://linshi.jncsjx.com We will have more wonderful content for you to see.