现在的玻璃工程越来越普遍，对打胶的要求也是越来越严格！于是一种方便快捷，质量可靠的打胶设备出现了--双组份打胶机！下面小编就给大家介绍一下这种打胶机的使用注意事项！
Now glass engineering is becoming more and more popular, and the requirement of gluing is becoming stricter and stricter. So a convenient, fast and reliable gluing equipment appeared - two-component gluing machine! The following edition will introduce to you the use of this type of glue beater notice points!
1.由于双组份密封胶的固化需要一定时间，因此，已涂了双组份密封胶的玻璃应水平轻轻搬动。
1. Since the curing of the two-component sealant takes a certain time, the glass coated with the two-component sealant should be moved horizontally and gently.
2.A组、B组份胶应保持清洁，严防异物进入胶中。
2. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
3.在连续工作过程中，胶枪每次停止工作时间一般不得超过20分钟，否则，应用A组份胶冲出全部混合胶，直至单一的A组份胶从枪口排出为止。
3. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, the whole mixture should be produced by using component A glue until a single component A glue is discharged from the muzzle of the gun.
4.高压胶管不得强行挤压、弯曲，防止影响系统正常工作。
4. High-pressure hose shall not be forced to extrude or bend to prevent the normal operation of the system.

5.混胶器应经常保持畅通，以保证良好的出胶效果。如遇堵塞情况，可用丙酮浸泡后清洗。建议每5组清洗一次。
5. Mixers should be kept unblocked regularly to ensure good gumming effect. In case of blockage, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.
6.当胶枪长时间不用时（超过一周），应拆下枪体使用溶剂将胶枪和混胶器内的残留胶体清洗干净。
6. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned with solvent.
7.不同双组份胶生产厂家所生产的胶内含杂质数量不同，根据实际情况清晰B组分的过滤网及单向止回阀，建议每两组清洗一次。
7. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, the filter screen and check valve with clear B component are recommended to be cleaned once for each two groups.
8.任何因胶体固化所造成的胶枪、管路或整机的故障，一律不在保修范围之内。
8. Any malfunction of rubber gun, pipeline or whole machine caused by gel solidification is not covered by warranty.
9.定期给各泵的加油口加油，应保证油雾器内不断油。
9. Regular refueling at the refuelling port of each pump should ensure continuous oil in the oil mist.
好了，今天的内容就暂且给大家介绍到这里了！以上的精彩内容由双组份打胶机的小编整理提供，更多的精彩内容请继续关注我们，我们会定期发布更多的精彩内容，请记住我们的官网：http://www.jncsjx.com
Okay, today's content will be introduced to you here for the time being! The above wonderful content is provided by the small edition of two-component glue machine. More wonderful content please continue to pay attention to us. We will release more wonderful content regularly. Please remember our official website: http://www.jncsjx.com.