1、双组份打胶机打胶之前注意观察打胶机的胶头是否有玻璃参差等异物出现，如果将其掺入密封胶内那么我们的中空玻璃的密封效果肯定就不会有那么好了。

　　1, before the glue, pay attention to observe the glue head of the glue machine, whether there is glass uneven and other foreign bodies appear, if it is mixed into sealant, then the sealing effect of our insulating glass will certainly not be so good.

　　2、打开气泵开关，电源总开关，控制台开关，在控制台按手动按钮，我们将打胶机胶头让他回位到原点，这是我们要对打胶机的速度进行下调节(一般情况下使用我们设置好的速度即可)，密封不严可能是由于打胶机的打胶速度过快而我们的铝条安装的时候深浅不一所以导致中空玻璃的密封胶在铝条深的地方会出现密封不严的情况。

　　2, open the pump switch, power switch, control switch, manual button on the console, we will glue machine glue head let him return to the origin, this is we want to fight the glue machine speed regulation (we use set speed under normal circumstances can), may be sealed and lax the glue machine glue fast and our aluminum strips when installing shades resulting in insulating glass sealant in aluminum deep place will be sealed and lax circumstance.

　　3、然后是混交了，按桶胶按钮，按工作选择按钮，然后按拍胶启动，在按伐开，此时胶头以出胶，等看不见白胶，以混均匀以后按伐关，此时我们就可以进行正常的打胶机工作了。

　　3, then is mixed, according to the first barrel of plastic button, and then press the select button according to the work, take glue start in cutting, the rubber head to glue, such as invisible glue, to mix well after the press cutting off, we can carry out normal atx-ii work at this time.

　　4、出现中空玻璃打胶机生产出来的中空玻璃密封不好的另一大主要原因就是我们的铝条安装过于随意~~~尽管我们的设备无需进行设置可全自动的检测并处理深浅不一的铝条，但是如果差距太大且打胶速度过快的话也是有可能发生中空玻璃密封不严漏气的情况。

　　4, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum strip is installed too freely while our equipment ~ ~ ~ without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.

　　5、打胶机的供娇压力如果不够的话也是会出现这个问题的，因为打胶机的胶体完全靠气压来挤出设备并的涂装在中空玻璃的铝条中的。如果压力过小的话也会导致中空玻璃打胶机密封不严

　　5, if the pressure of the glue machine is not enough, it will also appear this problem, because the glue of the glue machine is completely squeezed by the air pressure equipment, and perfectly painted in the aluminum strip of the insulating glass. If the pressure is too small, it will lead to the sealing of glass sealing machine is not strict

　　本文的精彩内容来自双组份打胶机详细内容请点击我们的网站:http://www.jncsjx.com谢谢您的到来

　　The wonderful content of this article comes from the two component dispenser, please click on our official website: http://www.jncsjx.com, thank you for coming