双组份打胶机的常见问题及处理方法

　　Common problems and solutions of two-component gluing machines

        一、胶水混合不均匀

　　1、 Uneven mixing of glue

　　双组份打胶机的胶水由两种不同的液体混合而成，如果混合不均匀，就会导致打出的胶水质量不稳定。该问题的主要原因是两种液体的比例不对或者胶水在混合过程中被污染。解决方法是检查混合比例是否正确，清洗胶水加料口以及胶嘴等部位。

　　The glue of the two-component glue machine is made by mixing two different liquids. If the mixing is not uniform, it will lead to unstable quality of the glue produced. The main reason for this problem is the incorrect ratio of the two liquids or contamination of the glue during the mixing process. The solution is to check if the mixing ratio is correct, clean the glue feeding port and the glue nozzle.

　　二、胶水流量不稳定

　　2、 Unstable glue flow rate

　　胶水流量不稳定是双组份打胶机常见的问题之一，可能是由于胶水中气泡过多、液压系统不完善或者胶嘴损坏等原因引起的。首先，检查胶水中的气泡是否完全排出，其次，检查液压系统是否运作正常，特别是是否存在泄漏情况，最后，检查胶嘴是否损坏。

　　Unstable glue flow rate is one of the common problems in two-component glue machines, which may be caused by excessive bubbles in the glue, incomplete hydraulic system, or damage to the glue nozzle. Firstly, check if the bubbles in the glue have been completely removed. Secondly, check if the hydraulic system is functioning properly, especially if there are any leaks. Finally, check if the glue nozzle is damaged.

　　三、胶水无法正常喷出

　　3、 Glue cannot be sprayed out normally

　　如果胶水无法正常喷出，可能是由于打胶机的空气压力不足、胶嘴堵塞或者液压系统出现故障等原因引起的。解决方法是检查空气压力是否合适，清洗胶嘴或更换胶嘴，还可以检查液压系统是否有故障。

　　If the glue cannot be sprayed normally, it may be caused by insufficient air pressure of the glue machine, clogged glue nozzle, or hydraulic system malfunction. The solution is to check if the air pressure is appropriate, clean or replace the nozzle, and also check if there is a malfunction in the hydraulic system.

　　四、胶水泡性、气泡过多

　　4、 Adhesive foaming, excessive bubbles

　　双组份打胶机打胶的质量直接影响产品的质量，如果胶水中含有大量气泡，就会导致胶水质量下降。该问题的主要原因是打胶机的压力不足、胶水中含有过多的气体或者管路中有空气等。解决方法可以提高打胶机的压力或排除气体，清洗管路中的空气。

　　The quality of the two-component glue machine directly affects the quality of the product. If there are a large number of bubbles in the glue, it will lead to a decrease in the quality of the glue. The main reasons for this problem are insufficient pressure on the glue machine, excessive gas in the glue, or air in the pipeline. The solution can be to increase the pressure of the glue machine or eliminate gas, and clean the air in the pipeline.

　　五、液压系统压力低

　　5、 Low hydraulic system pressure

　　如果双组份打胶机的液压系统压力低，将影响胶水的流量和稳定性。该问题的主要原因是液压系统中的油泵失效或油液污染等。解决方法是更换油泵或者清洗油液，确保液压系统正常工作。

　　If the hydraulic system pressure of the two-component glue machine is low, it will affect the flow rate and stability of the glue. The main cause of this problem is the failure of the oil pump or oil contamination in the hydraulic system. The solution is to replace the oil pump or clean the oil to ensure the normal operation of the hydraulic system.

　　本文由双组份打胶机提供技术支持，更多的详细精彩内容请点击我们的网站http://www.jncsjx.com，我们将会全心全意为您提供满意的服务。

　　This article is supported by a two-component gluing machine. For more detailed and exciting content, please click on our website http://www.jncsjx.com We will wholeheartedly provide you with satisfactory service.