双组份打胶机的注意事项
Points for attention of two component glue machine
双组份涂胶机是出产中空、幕墙玻璃的专用设备，可一次完成二道密封中A、B组份混合与涂胶。适用配比精度高的胶种，满足玻璃深加工企业高、高合格率流水线作业的出产需求，是大规模出产中空玻璃及玻璃幕墙产品的一种抱负的配套设备。
Two-component gluing machine is a special equipment for producing hollow and curtain wall glass. It can mix and glue components A and B in two seals at one time. It is suitable for mixing rubber with high precision and meets the production demand of high efficiency and high qualified rate pipeline operation in glass deep processing enterprises. It is an ideal matching equipment for large-scale production of high-quality hollow glass and glass curtain wall products.
1.因为双组份密封胶的固化需要一定时刻，因而，已涂了双组份密封胶的玻璃应水平轻轻搬动。
1. Because the curing of the two-component sealant takes a certain time, the glass coated with the two-component sealant should be moved horizontally and gently.
2.A组.B组份胶应保持清洁，严防异物进入胶中。
Group 2.A.B component should be kept clean and foreign matter should be strictly protected.
3.在接连工作过程中，胶枪每次停止工作时刻一般不得超过20分钟，否则，运用A组份胶冲出悉数混合胶，直单一的A组份胶从枪口排出停止。
3. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, use component A glue to punch out all the mixed glue until a single component A glue is discharged from the muzzle of the gun.

4.高压胶管不得强行挤压.弯曲，避免影响体系正常工作。
4. high pressure hose should not be forced to press. Bend to avoid affecting the normal work of the system.
5.混胶器应经常保持疏通，以确保杰出的出胶作用。如遇阻塞状况，可用丙酮浸泡后清洗。主张每5组清洗一次。
5. rubber mixer should be maintained regularly to ensure excellent glue production. In case of obstruction, acetone can be soaked and cleaned. It is advocated that every 5 groups be cleaned once.
6.当胶枪长时刻不用时（超过一周），应拆下枪体运用溶剂将胶枪和混胶器内的残留胶体清洗洁净。
6. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned by solvent.
7.不同双组份胶出产厂家所出产的胶内含杂质数量不同，根据实际状况清晰B组分的过滤网及单向止回阀，主张每两组清洗一次。
7. The amount of impurities in the gum produced by different two-component gum manufacturers is different. According to the actual situation, the filters and check valves with clear component B should be cleaned once for each two groups.
8.任何因胶体固化所形成的胶枪.管路或整机的毛病，一概不在保修范围之内。
8. Any defect of rubber gun, pipeline or whole machine caused by gel solidification is not covered by warranty.
9.定期给各泵的加油口加油，应确保油雾器内不断油。
9. regular refueling of each pump should ensure that the oil mist is constantly oil.
本文由济南昌盛机械http://www.jncsjx.com整理,我们将为您提供新的双组份打胶机知识，有兴趣的朋友可以关注我们，谢谢!!
This article is organized by Jinan Changsheng Machinery http://www.jncsjx.com. We will provide you with new knowledge of two-component gluing machine. Interested friends can pay attention to us. Thank you!