双组份打胶机的出现，给中空玻璃生产行业带来一股新的生机和活力。但是人无完人，机器也当然是如此，那么我们在使用中要注意哪些事项呢？我们接下来一起看看！
The emergence of two-component gluing machine has brought a new vigor and vitality to the hollow glass production industry. But no one is perfect, and so is the machine, so what should we pay attention to in the use? Let's take a look next!
1.由于双组份密封胶的固化需求一定时间，因而，已涂了双组份密封胶的玻璃应程度悄悄搬动。
1. Because of the curing time of the two-component sealant, the glass coated with the two-component sealant should be moved quietly.
2.A组、B组份胶应坚持清洁，严防异物进入胶中。
2. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
3.在连续工作过程中，胶枪每次中止工作时间普通不得超越20分钟，否则，应用A组份胶冲出全部混合胶，直至单一的A组份胶从枪口排出为止。
3. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, the rubber of component A should be used to punch out all the mixtures until a single component A is discharged from the muzzle of the gun.
4.高压胶管不得强行挤压、弯曲，避免影响系统正常工作。
4. High-pressure hose shall not be forced to extrude or bend to avoid affecting the normal operation of the system.

5.混胶器应经常坚持畅通，以保证良好的出胶效果。如遇梗塞状况，可用丙酮浸泡后清洗。倡议每5组清洗一次。
5. Mixers should always be unblocked in order to ensure a good gumming effect. In case of infarction, it can be washed after soaking in acetone. It is advocated to clean every five groups.
6.当胶枪长时间不用时（超越一周），应拆下枪体运用溶剂将胶枪和混胶器内的残留胶体清洗洁净。
6. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned by solvent.
7.不同双组份胶消费厂家所消费的胶内含杂质数量不同，依据实践状况明晰B组分的过滤网及单向止回阀，倡议每两组清洗一次。
7. The amount of impurities in the rubber consumed by different two-component rubber manufacturers is different. According to the practical situation, the filter screen and check valve of component B are clearly defined. It is suggested that each two groups be cleaned once.
8.任何因胶体固化所形成的胶枪、管路或整机的毛病，一概不在保修范围之内。
8. Any defect of rubber gun, pipeline or whole machine caused by gel solidification is not covered by warranty.
9.定期给各泵的加油口加油，应保证油雾器内不时油。
9. Regular refueling at the refuelling port of each pump should ensure that the oil mist is oiled from time to time.
好了，今天的内容就给大家介绍到这里了，更多关于双组份打胶机的精彩内容欢迎关注我们的官网：http://www.jncsjx.com
Well, today's content will be introduced to you here, more wonderful content about two-component glue machine welcome to pay attention to our official website: http://www.jncsjx.com