双组份打胶机供胶系统的清洗我们要把所有的管路阀门都拆解下来，拆解方法非常的简单用一般的扳手即可完成!

　　The cleaning of the glue system of the two-component glue machine, we must first disassemble all the pipeline valves, disassemble the method is very simple, can be completed with a general wrench!

　　当胶流速变慢或者混胶不均时清洗混合器。将混合器拆下横放在台钳上，夹住两端盖，不要夹到螺丝。用六角扳手松开两端的六条螺丝，打开器体，取出垫片，挡针，混合芯。将各个零件清洗干净。

　　Cleaning mixer when the flow velocity of gum is slow or uneven mixing. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Loosen the six screws at both ends with the six angle wrench, open the body, remove the gasket, stop the needle, and mix the core. Clean all parts.

　　端盖不要弄变形，各个平面不要有划伤。混合器一端有凹槽，安装时将其放进有挡针孔的一面，将挡针放入挡针孔，横放在凹槽上。

　　Do not deform the end cover, do not scratch each plane. The mixer end is provided with a groove, the installation will be put into the side of retaining the pinhole, will stop into the retaining needle pinhole, across the groove.

　　更换好垫片后将端盖对准器体，A对A，P对P，拧上螺丝，拧好后横放在台钳上夹紧，用扳手拧紧下端的四条螺丝，松开台钳，器体旋转300°，夹紧台钳，再拧紧下面四条螺丝。依次拧四五次即可。按A面进口，P面出口安装到胶机上即可。

　　Replace gasket after the end cap aligner, A to A, P to P, screw, screw after lying in a vise clamped by four screws, the lower end of the wrench to tighten loose vise device body is rotated 300 degrees, and then tighten the clamping vise below four screws. Turn it four or five times in turn. According to the A surface import, P surface outlet installed on the glue machine can.

　　打胶机Y型过滤器的位置在辅料泵出口处，清洗时将端盖拧下，用煤油浸泡，用牙刷类刷子刷干净。安装时将网放在端盖里用手拧到底，再用扳手拧紧。用一组胶洗一次，如无杂质两组胶洗一次，灵活掌握。

　　The position of Y type filter is at the outlet of auxiliary pump, and the end cover is screwed down when washing. It is soaked with kerosene and cleaned with toothbrush brush. The installation will be placed on the end cover by hand net screwed in the end wrench, tighten. Use a set of glue to wash once, such as no impurities, two groups of rubber wash once, flexible grasp.

　　清洗时将其拧下，用尖嘴钳拧下小螺母，拔出针体，弹簧。全部清洗干净。针阀出口平面及针帽确保无任何杂质，划伤，变形。安装时将针插入阀体，弹簧套在针体上，螺母大头向里面拧紧，力量在1到2公斤左右。

　　When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean all. Needle valve outlet plane and needle cap ensure no impurities, scratches, deformation. When installing, insert the needle into the valve body, the spring is sheathed on the needle body, the nut is screwed to the inside, and the power is about 1 to 2 kilograms.

　　打胶机大过滤器的位置在高压表B表右下，拧下回流阀下方胶管，拧下过滤器，将网及网芯取出，弹簧、取出，刷干净，将弹簧小孔套在网芯的凸点上。倒着裝入器体后转过来拧在胶机上。用3-5组洗一次，如无杂质，灵活掌握即可 。

　　The position of the big filter of the glue machine is in the right lower part of the B table of the high-pressure meter, the rubber hose below the reflux valve is screwed, the filter is screwed down, the net and the net core are taken out, the spring is taken out, the brush is cleaned, and the spring hole is sheathed on the convex point of the net core. Turn it upside down and load it on the rubber machine. Wash with 3-5 groups, such as no impurities, flexible control can be.

　　打胶机胶枪的枪口混合器清洗时直接拧下枪口混合器取出混合芯即可。清洗枪柄混合器时，先把枪上的定位螺丝松开，然后拧下枪柄混合器。枪口混合器同混合器同周期清洗;抢柄混合器同枪同周期清洗，半年或一年洗一次。

　　The muzzle mixer of the glue gun of the glue machine is directly screwed off the muzzle mixer when the cleaning is done, and the mixing core can be removed. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer. The muzzle mixer is cleaned with the same period of the mixer; the grab mixer is cleaned with the same period of the gun, and washed once or half a year.

　　以上便是双组份打胶机今天的分享，您还满意吗，欢迎关注我们的网站:http://linshi.jncsjx.com/并且关注我们的产品，我们将为您提供优良的产品，衷心的愿与您建立合作关系。

　　The above is to share the two-component glue machine today, you still satisfied with it, welcome to our website: http://linshi.jncsjx.com/ and pay attention to our products, we will provide you with excellent products, sincerely wish to establish business relationship with you.