在运用封胶机时要留意哪些事项：
What should we pay attention to when using sealant machine?
1.混合胶在胶枪内滞留工夫必需控制在3-5分钟内，否则蜂鸣器报警。
1. Mixed glue must be kept in rubber gun for 3-5 minutes, otherwise buzzer will alarm.
2.封胶之前要反省双组份胶的混合化，将胶挤到100mm的正方形，厚3mm的浮法玻璃上，再那一块异样的浮法玻璃在块玻璃上一压，在光亮处反省，如混合胶内有白丝或黑丝，即混合不平均。
2. Before sealing, we should reflect on the mixing of two-component glue, squeeze the glue onto a 100 mm square, 3 mm thick float glass, and then press the unusual float glass on the first glass, and reflect on the bright spot. If there is white or black silk in the glue, the mixing is uneven.
3.要时辰留意液压设备压力表（指针指在绿色平安，黄色、白色风险）。
3. Always pay attention to the pressure gauge of hydraulic equipment (pointer refers to green safety, yellow, white risk).
4.留意胶筒压力表（A组份胶6bar,B组份胶4bar）。
4. Pay attention to the pressure gauge of rubber cylinder (6bar for component A and 4bar for component B).
任务终了后，封闭设备，翻开胶枪，将胶枪内的胶全部挤出压力小于30bar，如长工夫不必，先将Operatingmade(操作形式开关)打BASEPURGE(基料冲洗)，再翻开胶枪，直A组份胶全部挤出，设备封闭，持续打胶直压力小于30bar后放入冷冻箱。
At the end of the task, close the equipment, turn over the rubber gun, and extrude all the glue in the glue gun at a pressure less than 30 bar. If it is not necessary for a long time, first hit the Operating Make (operation mode switch) to BASEPURGE (base material flushing), then turn over the glue gun until the A component glue is extruded completely, the equipment is closed, and continue to glue until the pressure is less than 30 bar, then put in. Freezer.
三角形点胶机是依据紧缩空气送入注射器内，将胶压入与活塞室相连的进给管中，当活塞处于上冲程时，活塞室中填满胶，当活塞向下推进滴胶针头时，胶从针嘴压出。
The triangle dispenser feeds the rubber into the syringe according to the compressed air. The rubber is pressed into the feed pipe connected with the piston chamber. When the piston is in the upper stroke, the piston chamber is filled with glue. When the piston pushes down the needle, the glue is pressed out from the nozzle.

三角形点胶机在日常任务中能够会呈现断胶的状况看，此时可反省胶水是不是有成绩。如胶水中含气泡或颗粒物，通常此种状况比拟罕见。点胶控制器也会由于其本身功能或任务中的不正常操作招致断胶状况的呈现。
The triangle dispenser can show the situation of breaking glue in daily tasks. At this time, we can reflect whether the glue has achieved good results. If there are bubbles or particulates in the glue, this situation is usually rare. The dispensing controller will also cause the breakage of glue due to its own function or abnormal operation in the task.
UV胶即紫外线固化胶。三角形点胶机厂家引见，若UV胶不出胶，先确定运用黑色的管路。不要间接添加UV胶在压力筒UV胶上。
UV adhesive is UV curable adhesive. Triangle dispensing machine manufacturers, if the UV glue does not glue, first determine the use of black pipeline. Do not indirectly add UV glue to pressure cylinder UV glue.
应先将原有UV胶放掉，再将UV胶倒入空的压力筒内，压力筒内的UV胶往往经过一段工夫后会发生气泡而形成出胶不波动。
The original UV glue should be released first, and then the UV glue should be poured into the empty pressure cylinder. After a period of time, the UV glue in the pressure cylinder will foam and form the glue without fluctuation.
综上所述有济南昌盛机械提供，想了解更多双组份打胶机知识，欢迎关注我们的网站：http://linshi.jncsjx.com谢谢支持！
In summary, all the above-mentioned Jinan Changsheng Machinery provides, want to know more about the two-component glue machine knowledge, welcome to pay attention to our website: http://linshi.jncsjx.com Thank you for your support!