双组份打胶机顾名思义，是用于输送或泵送胶液的设备。双组份上胶机设备主要用于输送高粘度的流体介质。今天我们来看看双组份打胶机桶的更换步骤。
　　As the name implies, the two-component dispenser is used for conveying or pumping glue liquid. The two-component sizing machine is mainly used to transport high viscosity fluid medium. Today, let's take a look at the replacement procedure of the two-component dispenser barrel.
　　1. 关闭气泵的入口压力。
　　1. Close the inlet pressure of the air pump.
　　2. 打开橡胶排泄阀，释放内部系统的压力。

　　2. Open the rubber drain valve to release the pressure of the internal system.
　　3.打开压力板吹管阀。
　　3. Open the pressure plate blow valve.
　　4. 将升降控制阀旋到“上”位置。
　　4. Turn the lifting control valve to the "up" position.
　　5. 压力板将从胶筒中升起，终与胶筒分离到合适的位置，代替胶筒。
　　5. The pressure plate will be lifted from the rubber cylinder and finally separated from the rubber cylinder to a suitable position to replace the rubber cylinder.
　　6. 从设备机架上拆下空胶筒。
　　6. Remove the empty cartridge from the equipment rack.
　　7. 关闭压盘吹管阀。
　　7. Close the pressure plate blow pipe valve.
　　8. 清洗压片的两个密封圈，使表面清洁。
　　8. Clean the two sealing rings of the tablet to make the surface clean.
　　9. 仔细检查新桶是否有凹痕或其他损坏。不要使用损坏的桶，因为这会损坏压板。
　　9. Check the new drum carefully for dents or other damage. Do not use a damaged bucket as this will damage the platen.
　　10. 将新胶桶置于设备底座中心，压板下方。
　　10. Place the new rubber barrel in the center of the equipment base and under the pressing plate.
　　11. 在阀瓣密封环上涂润滑脂(诺德森公司:900302)。
　　11. Apply grease to the disc seal ring (Nordson: 900302).
　　12. 拆卸排气和橡胶出口杠杆。
　　12. Remove the exhaust and rubber outlet levers.
　　13. 将升降控制阀移至“下”位置，慢慢将压力板移至开启的橡胶筒内。将升降控制阀移动到中间“空档”位置，可停止压力板的移动。
　　13. Move the lifting control valve to the "down" position, and slowly move the pressure plate to the open rubber cylinder. Move the lifting control valve to the middle "neutral" position to stop the movement of the pressure plate.
　　14. 连续压下压板。当排气口和排气口有稳定的胶流时，将排气口和排气口杠杆重新安装到压板上，并拧紧压板在接头上。
　　14. Press down the pressing plate continuously. When the exhaust port and exhaust port have stable glue flow, reinstall the exhaust port and exhaust port lever on the pressure plate, and tighten the pressure plate on the joint.
　　15. 完成换鼓步骤，打开气泵进气开关，正常工作。
　　15. Complete the drum changing step, turn on the air pump intake switch and operate normally.
　　以上是双组份打胶机厂家小编为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://linshi.jncsjx.com
　　The above is the relevant content introduced by the manufacturer of two-component gluing machine. If you want to know more, please visit the website: http://linshi.jncsjx.com