1、双组份打胶机操作：
1. Operation of two-component glue applicator:
1)松开份额杠杆上的份额泵锁紧螺钉，将份额泵表里调整至所需份额。只有当A胶和B胶的配比到达正常值时，才可进行下面的操作。
1) Loosen the locking screw of the share pump on the share lever, and adjust the share pump table to the required share. Only when the ratio of glue a and glue B reaches the normal value, the following operation can be carried out.
2)置挑选旋钮于A、B泵开，将胶枪出口对准两片玻璃的中缝，翻开胶枪开关，以恰当速度平稳地移动胶枪使玻璃槽内的双组份胶填满充实为佳。打胶结束时封闭胶枪。
2) Set the selection knob on pump a and pump B, align the glue gun outlet with the middle seam of the two pieces of glass, turn on the glue gun switch, and move the glue gun steadily at an appropriate speed to fill up the two-component glue in the glass tank. Close the glue gun at the end of gluing.
更换胶桶：1)当胶桶内的胶用完时，应立即封闭A、B开关，停止打胶。
Replace the rubber barrel: 1) when the glue in the rubber barrel is used up, the A and B switches should be closed immediately to stop the glue application.
2)翻开双组份打胶机A(或B)胶泵充气开关，挑选A(或B)胶泵提高组织为上升位置，点动旋钮使压盘慢慢提起，此刻应留意：胶桶尽量不要离开底盘，直至压盘完全脱离胶桶时封闭A(或B)胶泵的充气开关。
2) Turn on the inflation switch of a (or b) glue pump of the two-component glue applicator, select the a (or b) glue pump lifting organization as the rising position, and press the knob to slowly lift the pressure plate. At this moment, it should be noted that the rubber barrel should not leave the chassis as far as possible until the pressure plate is completely separated from the rubber barrel, and then close the inflation switch of a (or b) rubber pump.
3)双组份打胶机撤出空桶，将新胶桶置于工作位置，重复第3、4、项操作。
3) Withdraw the empty barrel of the two-component glue applicator, put the new rubber barrel in the working position, and repeat the operations of items 3, 4.
胶枪：因双组份胶是由两种胶混合而成的，其凝固速度与环境温度和A、B胶的份额有关，混合后的胶一般在20分钟之内就会反应固化。所以，当设备在正常打胶后，20分钟之内不运用就必须将混合后的胶冲洗出来，以免堵塞混胶器和胶枪。

Glue gun: because the two-component glue is made by mixing two kinds of glue, its solidification rate is related to the ambient temperature and the proportion of glue a and B. the mixed glue will react and solidify within 20 minutes. Therefore, when the equipment is not used within 20 minutes after normal gluing, the mixed glue must be washed out to avoid blocking the glue mixer and glue gun.
2、中空玻璃打胶机具体操作：将B泵封闭，翻开B胶回流开关然后翻开胶枪，至胶条为白色即可。洗枪：
2. The specific operation of insulating glass gluing machine: close pump B, turn on the return switch of glue B, and then turn on the glue gun until the adhesive strip is white. Gun washing:
3、把中空玻璃打胶机混合器放到水火烧，直到把混合芯拿出为至;注黑把手里边还有一结。混合器和枪头之间的旋转部位不可烧;枪头不可烧。可用铁丝打通为止
3. Put the mixer of the insulating glass gluing machine on the water and fire until the mixing core is taken out. There is a knot in the black injection handle. Do not burn the rotating part between mixer and gun head; do not burn gun head. It can be broken through with wire