一、接通气源：
1、 Connect the air source:
本机预留气管接口为PU12快插接头。
The reserved air pipe interface of this machine is pu12 quick plug connector.
气源接通，调节减压阀至0.4~0.6Mpa，检查系统有无漏气现象。然后试运行以下动作：（1）A泵提升；（2）A泵充气；（3）B泵提升；（4）B泵充气。注意：提升气缸提升时，如果两气缸不同步，请下降至原点后重新操作。
Connect the air source, adjust the pressure reducing valve to 0.4 ~ 0.6MPa, and check the system for air leakage. Then test run the following actions: (1) pump a lifting; (2) pump a charging; (3) pump B lifting; (4) pump B charging. Note: when lifting the lifting cylinder, if the two cylinders are not synchronized, please lower to the origin and operate again.
二、将A、B组份胶桶就位，并与A、B胶泵的轴线对中。双组份打胶机
2、 Put the rubber barrel of components a and B in place and align with the axis of rubber pump a and B. Two component gluing machine
以A组份为例：
Take component A as an example

操作手动转阀，将A泵提升至较高，提升过程中观察各管路有无拉伸过紧处。、将胶桶放置在A泵压胶盘下，开启胶桶，将其中塑料袋外翻至桶外，胶面塑料片取出。
Operate the manual rotary valve to lift pump a to a higher position. Observe whether the pipelines are stretched too tightly during the lifting process. Place the rubber barrel under the pressure plate of pump a, open the rubber barrel, turn the plastic bag out of the barrel, and take out the plastic sheet on the rubber surface.
使A泵压盘缓慢下降，压盘入桶时应使其与桶口对准，将压胶盘排气口打开，直到压盘接触胶面。待压盘内气体全部排放完并有少量胶从排气口溢出时，即可关闭排气阀。（提升开关保持下压状态）
Make the pressure plate of pump a drop slowly. When the pressure plate enters the barrel, align it with the barrel opening. Open the exhaust port of the pressure plate until the pressure plate contacts the rubber surface. When the gas in the pressure plate is completely discharged and a small amount of glue overflows from the exhaust port, the exhaust valve can be closed. (lift switch remains depressed)
开机试打胶：将主泵气源开关打开，按下胶枪开关，直至双组份打胶机A泵里空气排净枪口处出胶连续时停止。
Start up and test glue: turn on the air source switch of the main pump and press the glue gun switch until the air in the pump a of the two-component glue machine is drained and the glue is discharged continuously at the muzzle.
用同样的方法操作B泵。
Operate pump B in the same way.
功能特点：
Functional features:
气动双组份打胶机是集较技术生产的中空玻璃密封胶打胶机，A组分泵和B组分泵胶分别采用气动系统驱动，采用无触点电器控制系统控制，换向灵敏可靠，其独特的方便可调试配比机构，较大限度地保证双组份胶近乎苛刻的配比要求，出胶连续均匀，涂胶效果好，生产效率高。
Pneumatic two-component sealant machine is a set of domestic and foreign technology production of insulating glass sealant machine, a component pump and B component pump are driven by pneumatic system, using contactless electrical control system control, reversing sensitive and reliable, its unique convenient and adjustable proportioning mechanism, to a large extent to ensure that the two-component glue almost harsh proportioning requirements, glue continuous and uniform, glue effect Good fruit, high production efficiency.