初次使用双组份打胶机会有出胶不稳的情况，跟工人的操作熟练度和掌控度有关系，我这用了2天左右就熟练掌握了双组份打胶机的操作。除了操作熟练，应该跟机器的也有关系。我这用的济南皓德的，出胶还算稳定。这是它们公司的产品介绍：机架采用整体焊接，龙门架、焊接三角形构成稳定结构，克服悬臂梁工作时的摇动，B泵采用双立柱，压盘双道密封，彻底解决黑组份胶易氧化泄漏的难题；优化管路设计，解决产品流速慢的问题。
When I first used the two-component gluing machine, the glue was unstable, which was related to the operation proficiency and control of the workers. It took me about 2 days to master the operation of the two-component gluing machine. In addition to skilled operation, it should also have something to do with the of the machine. I use Jinan Haode, and the glue is stable. This is the product introduction of their company: the frame is welded as a whole, and the gantry and welded triangle form a stable structure to overcome the shaking of the cantilever beam during operation. Pump B adopts double columns and pressure plate double seals, which completely solves the problem of easy oxidation and leakage of black component glue; Optimize pipeline design to solve the problem of slow product flow rate.
因双组份打胶机是全气动控制机型，为了使用户更好地使用好该设备，故建议在使用前务必仔细阅读本说明书并严格遵照下列要求进行操作。
Since the two-component glue applicator is a fully pneumatic control model, in order to enable users to better use the equipment, it is recommended to carefully read this manual before use and operate in strict accordance with the following requirements.
一、接通气源：
1、 Connect the air supply:
本机预留气管接口为PU12快插接头。

The reserved air pipe interface of this machine is pu12 quick plug connector.
气源接通，调节减压阀至0.4~0.6Mpa，检查系统有无漏气现象。然后试运行以下动作：（1）A泵提升；（2）A泵充气；（3）B泵提升；（4）B泵充气。注意：提升气缸提升时，如果两气缸不同步，请下降至原点后重新操作。
Connect the air source, adjust the pressure reducing valve to 0.4 ~ 0.6MPa, and check the system for air leakage. Then test run the following actions: (1) pump a lifting; (2) A pump inflation; (3) B pump lifting; (4) B pump inflation. Note: when lifting the lifting cylinder, if the two cylinders are not synchronized, please lower to the original point and operate again.
二、将A、B组份胶桶就位，并与A、B胶泵的轴线对中。
2、 Put the rubber drums of components a and B in place and align them with the axis of rubber pumps a and B.
以A组份为例：
Take component A as an example:
1、操作手动转阀，将A泵提升至高，提升过程中观察各管路有无拉伸过紧处。
1. Operate the manual rotary valve to lift pump a to the maximum. During the lifting process, observe whether each pipeline is stretched or too tight.
2、将胶桶放置在A泵压胶盘下，开启胶桶，将其中塑料袋外翻至桶外，胶面塑料片取出。
2. Place the rubber bucket under the pressure plate of pump a, open the rubber bucket, turn the plastic bag out of the bucket, and take out the plastic sheet on the rubber surface.
3、使A泵压盘缓慢下降，压盘入桶时应使其与桶口对准，将压胶盘排气口打开，直到压盘接触胶面。待压盘内气体全部排放完并有少量胶从排气口溢出时，即可关闭排气阀。（提升开关保持下压状态）
3. Slowly lower the pressure plate of pump a, align the pressure plate with the barrel opening when entering the barrel, and open the exhaust port of the pressure plate until the pressure plate contacts the rubber surface. When all the gas in the pressure plate is discharged and a small amount of glue overflows from the exhaust port, close the exhaust valve. (lift switch remains depressed)
4、开机试打胶：将主泵气源开关打开，按下胶枪开关，直至A泵里空气排净枪口处出胶连续时停止。
4. Start up and try gluing: turn on the air source switch of the main pump and press the glue gun switch until the air in pump a is exhausted and the glue is continuously discharged from the muzzle.
用同样的方法操作B泵。
Operate pump B in the same way.
以上就是今天小编给大家提供的精彩内容，更多的精彩内容请点击进入我们的官方网站：双组份打胶机http://linshi.jncsjx.com
The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: two-component gluing machine http://linshi.jncsjx.com