全自动铝条折弯机的结构特点

　　Structural characteristics of fully automatic aluminum bar bending machine

　　铝条折弯机是一种能够对薄板进行折弯的机器，其结构主要包括支架、工作台和夹紧板，工作台置于支架上，工作台由底座和压板构成，底座通过铰链与夹紧板相连，底座由座壳、线圈和盖板组成，线圈置于座壳的凹陷内，凹陷顶部覆有盖板。使用时由导线对线圈通电，通电后对压板产生引力，从而实现对压板和底座之间薄板的夹持。

　　The aluminum bar bending machine is a machine that can bend thin plates. Its structure mainly includes a bracket, a workbench and a clamping plate. The workbench is placed on the bracket, and the workbench is composed of a base and a pressing plate. The base is connected with the clamping plate through a hinge. The base is composed of a base shell, a coil and a cover plate. The coil is placed in the recess of the base shell, and the top of the recess is covered with a cover plate. When in use, the coil is energized by the wire, which will generate gravity on the pressing plate, so as to achieve the clamping of the thin plate between the pressing plate and the base.

　　铝条折弯机结构特点:

　　Structural features of aluminum bar bending machine:

　　1、采用全钢焊结构，具有足够的强度和刚性;

　　1. All steel welding structure is adopted, with sufficient strength and rigidity;

　　2、液压上传动，机床两端的油缸安置于滑块上，直接驱动滑动工作;

　　2. Hydraulic upward transmission, the oil cylinders at both ends of the machine tool are arranged on the sliding block to directly drive the sliding work;

　　3、滑块同步机构采用扭轴强迫同步;

　　3. The slider synchronous mechanism adopts torsion shaft forced synchronization;

　　4、采用机械档块结构，稳定可靠;

　　4. Mechanical block structure is adopted, which is stable and reliable;

　　5、滑块行程机动快速调，手动微调，计数器显示;

　　5. The slider stroke can be adjusted quickly and manually, and the counter can be displayed;

　　6、斜楔式的挠度补偿机构，以保证获得较高的折弯精度。

　　6. Wedge type deflection compensation mechanism to ensure higher bending accuracy.

　　铝条折弯机保养与维护:

　　Maintenance of aluminum bar bending machine:

　　在进行机床保养或擦机前，应将上模对准下模后放下关机，直工作完毕，如需进行开机或其它操作，应将模式选择在手动，并确保。其保养内容如下：

　　Before machine tool maintenance or cleaning, the upper die should be aligned with the lower die, and then put down and shut down until the work is completed. If it is necessary to start up or perform other operations, the mode should be set to manual and ensure that. The maintenance contents are as follows

　　1、液压油路

　　1. Hydraulic oil circuit

　　1)每周检查油箱油位，如进行液压系统维修后也应检查，油位低于油窗应加注液压油;

　　1) Check the oil level of the oil tank every week. If the oil level is lower than the oil window, add hydraulic oil;

　　2)本机所用液压油为ISO HM46或MOBIL DTE25;

　　2) The hydraulic oil used in this machine is ISO HM46 or MOBIL DTE25;

　　3)新机工作2000小时后应换油，以后每工作4000～6000小时后应换油，每次换油，应清洗油箱;

　　3) The oil of the new machine should be changed after 2000 hours of operation, and after every 4000~6000 hours of operation, the oil tank should be cleaned every time;

　　4)系统油温应在35℃～60℃之间，不得超过70℃，如过高会导致油质及配件的变质损坏。

　　4) The system oil temperature shall be between 35 ℃ and 60 ℃, and shall not exceed 70 ℃. If it is too high, the oil quality and accessories will be deteriorated and damaged.

　　2、过滤器

　　2. Filter

　　1)每次换油时，过滤器应更换或*清洗;

　　1) The filter shall be replaced or cleaned every time the oil is changed;

　　2)机床有相关报警或油质不干净等其它过滤器异常，应更换;

　　2) If the machine tool has related alarms or other filters are abnormal, such as dirty oil, they should be replaced;

　　3)油箱上的空气过滤器，每3个月进行检查清洗，1年更换。

　　3) The air filter on the oil tank shall be checked and cleaned every 3 months and replaced every 1 year.

　　3、液压部件

　　3. Hydraulic components

　　1)每月清洁液压部件(基板、阀、电机、泵、油管等)，防止脏物进入系统，不能使用清洁剂;

　　1) Clean hydraulic components (baseplate, valve, motor, pump, oil pipe, etc.) every month to prevent dirt from entering the system, and do not use detergent;

　　2)新机使用一个月后，检查各油管弯曲处有无变形，如有异常应予更换，使用两个月后，应紧固所有配件的连接处，进行此项工作时应关机，系统无压力。

　　2) After the new machine has been used for one month, check whether there is deformation at the bending of each oil pipe. If there is any abnormality, replace it. After two months of use, fasten the connection of all accessories. Shut down the machine when doing this work, and the system has no pressure.

　　铝条折弯机工作原理:

　　Working principle of aluminum bar bending machine:

　　液压折弯机包括支架、工作台和夹紧板，工作台置于支架上，工作台由底座和压板构成，底座通过铰链与夹紧板相连，底座由座壳、线圈和盖板组成，线圈置于座壳的凹陷内，凹陷顶部覆有盖板。

　　The hydraulic bending machine consists of a support, a workbench and a clamping plate. The workbench is placed on the support. The workbench is composed of a base and a pressing plate. The base is connected with the clamping plate through a hinge. The base is composed of a base shell, a coil and a cover plate. The coil is placed in the recess of the base shell, and the top of the recess is covered with a cover plate.

　　使用时由导线对线圈通电，通电后对压板产生引力，从而实现对压板和底座之间薄板的夹持。由于采用了电磁力夹持，使得压板可以做成多种工件要求，而且可对有侧壁的工件进行加工。折弯机可以通过更换折弯机模具，从而满足各种工件的需求。

　　When in use, the coil is energized by the wire, which will generate gravity on the pressing plate, so as to achieve the clamping of the thin plate between the pressing plate and the base. Because of the electromagnetic force clamping, the pressing plate can be made into a variety of workpiece requirements, and the workpiece with side wall can be processed. The bending machine can meet the needs of various workpieces by replacing the bending machine die.

本文由全自动铝条折弯机提供技术支持，更多的详细精彩内容请点击我们的网站http://www.jncsjx.com我们将会全心全意为您提供满意的服务。