
双组份打胶机常见问题必知的解决措施?
时间:2020-04-06 来源:http://www.jncsjx.com/ 发布人:昌盛机械
双组分橡胶制造机的中空玻璃设备常用的产品,在购买低价格或二手设备有时会有一些问题,这些问题是如何解决宏观信息来源?
There are some problems when purchasing low price or second-hand equipment for the commonly used products of insulating glass equipment of two-component rubber manufacturing machine. How to solve these problems is the macro information source?
是生产过程
First, the production process
双密封过程中,一道密封是丁基橡胶,其主要作用是将铝带固定在适当的位置,减少水蒸气和气体在边缘的渗透。中空玻璃第二密封胶由硅酮密封胶、聚硫醚密封胶和聚氨酯密封胶组成,分为结构总成和非结构总成。第二种密封胶在中空玻璃中的作用是:一是起密封作用,即保持空气层的气体,使中空玻璃的性能得以保持;二是起到粘结作用,即各部件紧密连接在一起,保持中空玻璃的结构稳定性。
In the double seal process, the first seal is butyl rubber, which is mainly used to fix the aluminum strip in a proper position and reduce the penetration of water vapor and gas at the edge. The second sealant for hollow glass is composed of silicone sealant, polysulfide sealant and polyurethane sealant, which is divided into structural assembly and non structural assembly. The function of the second sealant in the insulating glass is: first, it plays a sealing role, that is, to keep the air layer gas, so that the performance of the insulating glass can be maintained; second, it plays a bonding role, that is, the components are closely connected to maintain the structural stability of the insulating glass.
第二部分分析了双组份胶机更常见的解决问题——不粘锅
The second part analyzes the most common problem of two-component glue machine: non stick pot
1. 是否按照规范要求提前进行兼容性测试
1. Whether the compatibility test is conducted in advance according to the specification requirements
2. 在养护时间短、养护温度低(尤其是冬季)时进行剥离粘结试验。
2. Peel and bond test shall be carried out when the curing time is short and the curing temperature is low (especially in winter).
3、中空玻璃胶泵压力不够,导致胶液混合不均匀,粘接效果差,且容易造成封头压力不足,胶接头不密(密度不够)
3. The pressure of the insulating glass glue pump is not enough, which leads to uneven mixing of glue liquid and poor bonding effect, and it is easy to cause insufficient pressure of the head and poor density of glue joint
4. 设备故障导致搅拌效果不佳。如果橡胶机的气缸垫片磨损,就会导致固化剂混入橡胶中不一致,AB泵工作行程不同步或不匹配,AB组分混合不均匀,花胶。有些刚涂完的胶不出检查,如胶水干了,就会看不透玻璃花胶。连续挤压试验可用于确定在平板上前后生产三至五分钟的蛇纹石密封胶,使泵运行至少两个周期以检查异常情况(所谓的软点)。
4. Equipment failure leads to poor mixing effect. If the cylinder gasket of the rubber machine is worn, it will lead to inconsistent mixing of curing agent into the rubber, asynchronous or mismatched working stroke of AB pump, uneven mixing of AB components and glue. Some of the glue just applied can't be inspected. If the glue is dry, it will not be able to see through the cellophane. The continuous extrusion test can be used to determine the production of serpentine sealant for three to five minutes before and after the plate, allowing the pump to run for at least two cycles to check for abnormal conditions (so-called soft spots).
5. 在双组份制胶机上混合不同厂家的AB胶
5. Mix the AB glue of different manufacturers on the two-component glue making machine
6、溶剂不符合要求,或不干燥等。需要特别注意的一点是胶黏剂在固化阶段,胶黏剂的固化与胶黏剂的粘结是独立的,也就是说,胶黏剂要完全固化,并不意味着胶黏剂与基材要建立完全的粘结。对于双组分尤其如此。因此,重要的是要让玻璃单元有足够的时间来建立粘结,然后再施加应力。
6. The solvent does not meet the requirements, or does not dry, etc. Special attention should be paid to the fact that in the curing stage, the curing of the adhesive is independent of the bonding of the adhesive, that is to say, the complete curing of the adhesive does not mean the complete bonding between the adhesive and the substrate. This is especially true for two components. Therefore, it is important to allow sufficient time for the glass element to establish the bond before applying the stress.
以上就是双组份打胶机更常见的解决问题的解决措施的详细介绍,想要了解更多请点击官网http://www.jncsjx.com
The above is a detailed introduction of the most common solutions to the problems of the two-component dispenser. To learn more, please click http://www.jncsjx.com
- 全自动封胶线是工业制造的高效粘结助力! 2025/03/18
- 中空玻璃加工设备怎么开启高效节能玻璃制造新时代? 2025/03/18
- 你知道中空玻璃生产线是建筑玻璃制造的核心力量吗? 2025/03/17
- 封胶线生产玻璃的流程是什么 2025/02/28
- 中空玻璃生产线:用科技与创新,重新定义玻璃深加工 2025/02/22
- 全自动铝条折弯机:智能制造时代的精密加工利器 2025/02/20
- 中空玻璃全自动封胶线的应用范围有哪些 2025/02/17
- 中空玻璃全自动封胶线有哪些优势 2025/02/15
- 双组份打胶机:工业生产的高效密封利器 2025/02/13
- 中空玻璃加工设备选型要点 2025/02/10