双组份打胶机在咱们平常的使用过程中有许多需求留意的事项，假如咱们平常不留神留意这些地方很可能会形成咱们的双组份打胶机呈现各式各样的毛病。这样不光影响你的出产功率降低你的收益还会大幅度的降低设备的寿命
There are many things we need to pay attention to in our normal use of the two-component dispenser. If we don't pay attention to these places, it is likely that our two-component dispenser will present various problems. This will not only affect your production power, reduce your revenue, but also significantly reduce the life of the equipment
今天小编就介绍下关于双组份打胶机在平常出产操作中究竟应该留意哪些方面。各位可以依照小编所写的内容严格执行操作，以免呈现各种不必要的问题以及毛病。
Today's small edition on the introduction of two-component sizing machine in the ordinary production operation should pay attention to which aspects. You can strictly follow the contents of the editor to avoid unnecessary problems and problems.
一、需要注意的事项
1、 Precautions
1、压盘上的放气阀门要保持晓畅，要定时疏通和清洗。
1. The air release valve on the pressure plate shall be kept clear, dredged and cleaned regularly.
2、正常作业时不要断气源，假如发现断气源应中止作业。
2. Do not cut off the air source during normal operation. If any, stop the operation.
3、若双组份打胶机涂胶作业过程中停顿时刻超过15分钟以上时，必定要用“冲枪”。本机有报警功能，届时没有冲胶会有蜂鸣器报警。
3. If the pause time is more than 15 minutes in the process of two-component gluing machine gluing operation, it is necessary to use "shot gun". This machine has an alarm function. There will be a buzzer alarm if there is no glue flushing.
4、定时查看气源，应确保使用经干燥的洁净压缩空气，并定时排放别离过滤器中的积水，查看油雾器中的油是否够用。
4. Check the air source regularly. First, make sure to use dry and clean compressed air, regularly discharge the accumulated water in the separate filter, and check whether the oil in the oil atomizer is sufficient.
5、硅酮胶B 组份遇空气会结壳，影响泵的正常作业和管路的疏通，因而，停机时B组份胶的一切通道在泄压后均应关闭，使B组份不得接触空气。
5. In case of air, component B of silicone rubber will crust, which will affect the normal operation of the pump and the dredging of the pipeline. Therefore, all channels of component B rubber shall be closed after pressure relief during shutdown, so that component B shall not contact the air.

6、B胶桶内假如要有空气，空气将排不出来，B泵将快速往复运动，不能向高压泵内正常供胶，影响整个系统，因而，必须将空气排出来。办法是：将压盘提出重新压入并放气。
6. If there is air in the B rubber barrel, the air will not be discharged, and the B pump will move rapidly to and fro, and cannot supply glue to the high pressure pump normally, which will affect the whole system. Therefore, the air must be discharged. The method is: lift the pressure plate and press it in again and release the air.
7、液压站系统的压力，不能调的太高，要根据室内环境温度等实际情况，调至满意胶嘴正常出胶均匀打胶即可。翻开液压站时必定要翻开胶枪，否则B组份管路压力将升得很高，形成安全事故。
7. The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as the indoor environment temperature, adjust the pressure to the satisfaction that the glue nozzle is normal and the glue is evenly applied. When opening the hydraulic station, the glue gun must be opened, otherwise the pressure of component B pipeline will rise very high, forming a safety accident.
8、A胶提胶泵接连作业1分钟以上没有供胶中止，说明管路内有空气，此刻会报警，须翻开泵上管接头再翻开A胶提胶泵，直到出胶中止，中止并接好接头，胶枪会呈现有空气的哔哔爆炸声，空气排净就好了。
8. The continuous operation of a glue lift pump for more than 1 minute does not stop the supply of glue, which means there is air in the pipeline. At this moment, an alarm will be given. It is necessary to open the upper pipe joint of the pump and then the a glue lift pump until the delivery of glue is stopped. Stop and connect the joint. The glue gun will show an air beep explosion, and the air will be discharged completely.
9、因为每次冲洗混合器不会完全洁净，每次都有少量的混合胶堆积，越来越多，致使堵塞混合器通道，用一段时刻后，影响出胶量和混合效果，因而要定时(聚硫胶五天，硅酮胶两天)清洗混合器。把混合器内的混胶棒拆出，如有损坏替换新的混胶棒。若混胶棒拆不出来，可用火烧掉，留意不能损伤零件螺纹。
9. Because the mixer will not be completely clean every time, a small amount of mixed rubber will accumulate every time, more and more, which will block the mixer channel. After a period of time, the rubber output and mixing effect will be affected, so it is necessary to clean the mixer regularly (polysulfide rubber for five days, silicone rubber for two days). Remove the mixing bar in the mixer, and replace it with a new one if it is damaged. If the rubber mixing rod cannot be removed, it can be burnt out by fire. Pay attention not to damage the thread of parts.
二、双组份打胶机设备保养
2、 Maintenance of two-component gluing machine
双组份打胶机的清洁喷枪表面、清理喷嘴，确保喷嘴的疏通;
Clean the surface of the spray gun and the nozzle of the two-component gluing machine to ensure that the nozzle is unblocked;
清洁或替换胶机和喷枪的过滤网;
Clean or replace the filter screen of glue machine and spray gun;
查看喷枪是否有漏胶现象，如有漏胶现象请调理，维修、替换喷枪、喷头、喷嘴等需求替换的部件。
Check whether the spray gun has leakage. If there is leakage, please adjust, repair and replace the spray gun, nozzle, nozzle and other parts that need to be replaced.
查看胶缸内壁是否有炭化层，如有炭化层请使用诺信专用清洗液R溶剂清洗胶缸。
Check whether there is a carbonized layer on the inner wall of the rubber cylinder. If there is a carbonized layer, please clean the rubber cylinder with the special cleaning solution r of nuoxin.
将胶机加热至操作温度，排空胶箱内的热溶胶。查看胶缸内是否有杂质，如有杂质用洁净的抹布清洁胶缸。
Heat the glue machine to the operating temperature and empty the hot-melt glue in the glue box. Check whether there are impurities in the rubber cylinder. If there are impurities, clean the rubber cylinder with a clean cloth.
查看双组份打胶机的一切接线盒和接线柱是否结实;
Check whether all junction boxes and terminals of the two-component dispenser are firm;
查看一切电源衔接线是否有破损现象，其他绝缘件是否牢靠;
Check whether all power plug wires are damaged and other insulation parts are secure;
清洁及查看胶机电器箱内部;
Clean and check the inside of the rubber machine electrical box;
查看双组份打胶机的一切电源衔接线衔接是否牢靠。
Check whether all power pins of the two-component dispenser are firmly connected.