双组份打胶机控制体系采用PLC和触摸屏，人机界面，一键操作。该设备操作简略，运用方便。伺服控制体系选用世界名牌(日本安川)，功能更稳定。满意设备运转要求，玻璃污染可忽略不计。只需一人操作设备即可完结整块玻璃的上胶。稳定可靠，出产效率高。双组份打胶机由A、B胶泵、气动体系、升降结构、机架等组成。那么在运用双组份打胶机时留意什么问题呢?让我们来了解一下。
PLC and touch screen are used in the control system of the two-component gluing machine, with man-machine interface and one key operation. The equipment is simple to operate and easy to use. The servo control system adopts the world famous brand (Yaskawa, Japan), with more stable functions. The glass pollution can be ignored. Only one person can operate the equipment to finish the gluing of the whole glass. Stable and reliable, high production efficiency. The two-component gluing machine is composed of a and B glue pumps, pneumatic system, lifting structure, frame, etc. So what problems should we pay attention to when using the two-component gluing machine? Let's have a look.
1. 因为双组份打胶机的固化需求必定的时刻，所以涂有双组份密封剂的玻璃需求水平移动。
1. Because the curing requirement of the two-component sealant is certain, the glass coated with the two-component sealant needs to move horizontally.
2. A组和B组的胶要保持清洁，严禁异物进入胶内。
2. The glue of group A and group B should be kept clean, and no foreign matter is allowed to enter the glue.
3.连续运转过程中，胶枪中止时刻不超越20分钟。否则，应运用胶水的组成部分冲刷一切混合的胶水，直到一个单一的组成部分的胶水从枪口排出。
3. During continuous operation, the stop time of glue gun shall not exceed 20 minutes. Otherwise, the glue components should be used to flush all mixed glue until a single component of glue is discharged from the muzzle.

4. 不得强行挤压或曲折高压软管，以免影响体系的正常运转。
4. Do not squeeze or bend the high-pressure hose by force to avoid affecting the normal operation of the system.
5. 混合器应始终保持疏通，以确保杰出的粘合剂作用。若阻塞，浸泡后用丙酮冲刷。主张每5套洗一次。
5. The mixer should be kept clear at all times to ensure excellent adhesive effect. If blocked, wash with acetone after soaking. Wash every 5 sets.
6. 当胶枪长时刻不运用(超越一周)时，应将胶枪本体取出，用溶剂清洗胶枪和混合器内残留的凝胶。
6. when the rubber gun is not used for longer than a week, the rubber gun body should be removed and the residual gel in the rubber gun and mixer should be cleaned with solvents.
7. 不同双组份打胶机出产的胶中杂质的含量不同。根据实际情况，B组件的滤网和单向止回阀每两组清洗一次。
7. The content of impurities in the glue produced by different two-component gluing machines is different. According to the actual situation, the filter screen and one-way check valve of assembly B are cleaned once every two groups.
8. 因为胶枪、管道或机器的胶态固化而形成的任何缺陷都不在保修范围内。
8. Any defects caused by glue curing of glue gun, pipe or machine are not covered by warranty.
9. 定时向双组份打胶机各泵的加油口加注油，确保油在雾化器内继续存在。
9. Add oil to the oil filler of each pump of the two-component glue applicator regularly to ensure that the oil continues to exist in the atomizer.
以上就是对双组份打胶机留意事项的详细介绍，想要了解更多请关注公司网站：http://linshi.jncsjx.com后续会呈现更多精彩内容。
The above is a detailed introduction to the matters needing attention of the two-component gluing machine http://www.jncsjx.com More exciting content will be presented later.