1、A组份提胶由电动齿轮泵提供，经管道输送至油压驱动的A胶高压柱塞泵增压。B组份提胶由气动往复泵提供，经管道输送至油压驱动的B组分高压柱塞泵增压。
　　1, A component extract is supplied by electric gear pump, and the A rubber high pressure plunger pump is pressurized by pipeline to oil pressure. B component extract is supplied by pneumatic reciprocating pump, and the B component high pressure plunger pump is pressurized by pipeline to oil pressure.
　　A、B胶的体积比例由双组分比例调节机构调整，然后，同时送入打胶机混合器，混合器由36节以上混合装置组成，双组份胶充分混合后到达涂胶枪，从胶嘴喷出，涂布于中空玻璃的边缘进行封边。胶嘴设有启动快速关闭阀，用以准确控制出胶时间。
　　The volume ratio of A, B glue by the two-component proportion regulating mechanism, and at the same time, into the glue mixer, the mixer is composed of 36 sections above the mixing device, two-component adhesive after mixing to glue gun, glue from the spout, the edge is coated on the insulating glass edge. The glue nozzle has the start quick closing valve, which is used to accurately control the glue time.
　　2、双组份供胶机主要有A组份提胶泵、B组份提胶泵， A、B胶增压装置，高压柱塞泵，A、B胶泵连接装置，双组分比例调节机构，高压出口安全分流装置，液压控制系统，气动控制系统及电器控制系统等组成。

　　2, two-component glue machine mainly has A components and B components of gel extraction pump rubber pump, A, B glue pressurizing device, high pressure piston pump, A pump, B glue connecting device, double component ratio adjusting mechanism, a high pressure outlet safety shunt device, hydraulic control system, pneumatic control. System and electrical control system.
　　3、供胶机的B组份胶出口处设有放泄阀，可以放气或泄压回流用，同位置还设置了超压回流的安全装置。在机头上进入混合器之前设有关断球阀和单向止回阀，防止A、B组份胶互串，造成固化而堵塞通道。
　　3. There is a vent valve at the B glue outlet of the glue feeder, which can release gas or pressure reflux, and also set a safety device for overpressure reflux in the same position. Before entering the mixer, a shut-off ball valve and a one-way check valve are set up to prevent the A and B components from interconnected, causing curing and blocking the channel.
　　4、A、B组份体积比例调节由双组分比例调节机构完成。 A、B组份比例分配比的调节主要靠调节高压泵前端连轩上的滑块，向上调B胶出胶少，向下调B胶出胶多。滑块中心距上端轴中心线16.4cm时，A/B胶的比例为10比1。
　　The volume proportion of the 4, A and B components is adjusted by the double component proportional regulation mechanism. The proportion distribution ratio of A and B is regulated mainly by adjusting the slider on the front of the high pressure pump, less glue out of B glue, and more glue out of B. When the center of the slider is from the center line of the upper end axis 16.4cm, the proportion of A/B glue is 10 to 1.
　　本文由双组份打胶机为您提供，我们的网站是:http://linshi.jncsjx.com我们将以全心全意的热情为您提供更优质的服务，欢迎您的访问！
　　This article is provided by two component glue machine. Our website is: http://linshi.jncsjx.com, we will provide you with better service with wholehearted enthusiasm, welcome your visit.