1. When carrying out disassembly, maintenance and repair work, workers should not wear earrings, watches, necklaces, bracelets and other conductive ornaments to prevent accidents.

2. 在进行保养维修热熔胶涂布机的工作之前，必须先把热熔胶涂布机械上的电源用户及联拉外界的总电源给切断，不得带电操作。

2. Before maintenance and repair of the hot melt adhesive coating machine, the power user of the hot melt adhesive coating machine and the main power supply of the external coupling must be cut off first, and live operation is not allowed.

3、不要随便拆卸检查调整热熔胶涂布机上之任何零件，除非你对设备性能有足够了解。

3. Do not disassemble, check and adjust any parts on the hot melt adhesive coating machine, unless you have sufficient knowledge of the equipment performance.

4、除非有其他人员在旁边协助，并且在发生意外，因机械的损坏或人员的受伤时，可以即刻给于帮助或急救，否则不要单独对热熔胶涂布机设备进行拆装与维修。

4. Do not disassemble and repair the hot melt adhesive coater equipment separately unless there are other personnel nearby for assistance and immediate help or first aid can be given in case of accident, mechanical damage or personal injury.

5、只有合格的人员才可以对热熔胶涂布机进行维修保养的工作。

5. Only qualified personnel can repair and maintain the hot melt adhesive coating machine.

6、在任何情况下,不要随意触碰可能暴露于外界的电线接头或其他有电线联接且未松脱之元件。

6. Under any circumstances, do not touch the wire connectors or other components connected by wires that may be exposed to the outside without looseness.

7、拆卸或移动热熔胶涂布机上之保护装置或更换元器元件之前，必须先切断电源的供应。

7. Before removing or moving the protective device on the hot melt adhesive coating machine or replacing the element, the power supply must be cut off first.

8、如果可能的话，尽量站在塑胶毯上进行保养维修的工作。千万不要在有淹水的地板或非常潮湿的环境下对热熔胶涂布机进行维护工作。

8. If possible, try to stand on the plastic blanket for maintenance. Do not carry out maintenance work on the hot-melt adhesive coating machine in a flooded floor or in a very humid environment.

9、对热熔胶涂布机进行维护与维修时必须穿戴安全手套、护目镜及长袖工作服，避免身体部份被高温的液态热溶胶烫伤，或被高温的元件表面灼伤。

9. Safety gloves, goggles and long-sleeved work clothes must be worn during the maintenance and repair of the hot melt adhesive coating machine to prevent the body part from being scalded by the hot liquid hot melt adhesive or the surface of the hot element.

10、松脱或安装压力接头时，必须确定为热熔胶涂布机提供压力气源的压力已减低至零值。

10. When loosening or installing the pressure joint, it must be ensured that the pressure of the pressure air supply for the hot melt adhesive coater has been reduced to zero.

11、清洗热熔胶熔胶缸时，避免使用有焰火或尖锐的硬质工具，以免刮伤胶桶内部的铁氟龙不粘胶涂层。

11. When cleaning the hot melt glue cylinder, avoid using hard tools with fireworks or sharp edges to avoid scratching the Teflon non-stick coating inside the rubber barrel.