玻璃打胶机的出产产线
Production line of glass gluing machine
中空玻璃出产线首要有四段：入料段、清洗单调段、检查段和合片段。四段均以相同的倾角立式安放，结构紧凑、经济实用、功率高、维护便当。清洗箱为不锈钢材料制造，传送辊为耐酸 碱橡胶辊;通过有机玻璃视窗可随时便当地查询玻璃清洗状况;入料段、清洗单调段选用手动无级调速电机传动，玻璃以佳的速度平稳地工作。单调段选用大风力歪斜风刀能使玻璃表面得以枯 燥。检查段设有灯管，能清楚地检查玻璃的清洗质量;合片段具有玻璃定位及铝框定位设备，能结束玻璃定位、铝框定位安放功用。玻璃由传送胶辊承托及传送，传送辊由电机(辊压段电机)经 过变频调速器通过链轮带动，玻璃由清洗单调段低速进入本段，经检查合格后加速工作下一作业段，进步作业功率;由变频调速器控制本段调速电机的工作速度，光电开关控制玻璃进入下一 作业段。
There are four main sections for insulating glass production line: feeding section, cleaning monotone section, inspection section and closing segment. The four sections are placed vertically in the same dip angle, compact, economical and practical, high power and convenient maintenance. The cleaning box is made of stainless steel and the conveyor roll is acid and alkali resistant rubber roll. The glass cleaning condition can be inquired conveniently and locally at any time through the plexiglass window. The manual stepless speed regulating motor is used for the feeding section and the monotonous cleaning section, and the glass works smoothly at the best speed. The use of large wind deflection blades can make the surface of the glass dull. The inspection section is equipped with a lamp tube, which can clearly check the glass cleaning quality; the combination section has the glass positioning and aluminum frame positioning equipment, which can end the glass positioning, aluminum frame positioning and placement functions. Glass is supported and transported by conveyor cots, conveyor cots are driven by motors (roll section motors) through frequency converters through sprockets, glass is cleaned by monotonous low-speed into this section, after checking up to speed up work to the next section, improve operating power; by frequency converter governor to control the speed of this section of the speed control motor, optoelectronic. The switch controls the glass into the next operation section.
中空玻璃出产线粘着磨损，在切向力的作用下，抵触副表面的吸附膜和服污膜遭到损坏，使表面的轮廓峰在彼此作用的各点处发生冷焊，由于相对运动，材料便从一个表面转移到另一个外 表，构成粘着磨损。
Under the action of tangential force, the adsorptive film and the clothing fouling film on the surface of the pair are damaged. The surface contour peaks are cold welded at the points where they interact. Due to relative movement, the material is transferred from one surface to another, forming adhesive wear.
中空玻璃打胶机  丁基涂胶机 功用特征选用PC控制系统，定位，传送，涂胶可自动结束，气液增压系统控制，安稳可靠，涂胶均匀，胶量，不锈钢作业台面便于清理，首要元器件云 选用知名
The price of hollow glass gluing machine butyl gluing machine function features selection of PC control system, positioning, transmission, gluing can be automatically terminated, gas-liquid pressurization system control, stable and reliable, uniform glue coating, glue volume, stainless steel table surface easy to clean up, the main component cloud selection of well-known brands

中空玻璃设备的运用越来越广泛,在设备给我们供给赢利的时分我们也不能遗忘他们也需求"呵护",下面简略介绍一下中空玻璃设备的保养事项:
Hollow glass equipment is more and more widely used, and we can not forget that they also need "care" when the equipment provides us with a profit. Here is a brief introduction to the maintenance of hollow glass equipment.
1.中空玻璃设备摆角板前后支撑及其它活动处要常常注入润滑油.
1. the insulating glass equipment is often injected with lubricating oil before and after the supporting plate and other parts of the swing board.
2.中空玻璃设备每作业5000小时后,应对机头主轴箱的角触摸球轴承及深.沟轴承进行清洗,增加NBU-15润滑脂或锂基润滑脂(增加量为内腔面积的1∕3~2∕3左右,轴承达不到精 度时可替换.
2. After 5000 hours of operation, the angle touch ball bearings and deep groove bearings of the spindle box of the head should be cleaned, and the NBU-15 grease or lithium grease should be added (the increase is about 1_3~2_of the inner cavity area, and the bearings can be replaced if the accuracy is not reached.
3.中空玻璃设备床身导轨及机头两导轴应常常加注润滑油.
3. insulating glass equipment bed guide and head two guide shaft should often be lubricated.
4.中空玻璃设备机头要保持清洁,每个作业班非必须及时切屑,除去导轨及机头外面及内部的尘土和切屑,导轨外出头运用机油涂抹均匀.
4. Hollow glass equipment head to keep clean, each shift must not timely chip, remove the dust and chips outside and inside the guide rail and the nose, the use of oil smear evenly.
玻璃清洗单调机 功用特征 清洗区和水路系统悉数选用不锈钢材料制造，经久耐用，起浮规划的清洗传送安排，适宜清洗3-8MM厚的玻璃，清洗机的传送系统选用智能机械无极调速，完结 清洗机的高功率运用，共同单调规划，保证单调作用，下降能耗。
Functional Features of Glass Cleaning Monotone Cleaning Zone and Waterway System are all made of stainless steel, durable, floating planned cleaning and transmission arrangements, suitable for cleaning 3-8MM thick glass, the transfer system of the cleaning machine adopts intelligent mechanical infinite speed regulation, finishing the high power use of the cleaning machine, common monotone planning, guarantee Monotonous effect, reduce energy consumption.
文章由济南昌盛机械 ，对双组份打胶机感兴趣的朋友可以关注我们http://linshi.jncsjx.com，敬请期待更多精彩内容。
The article is from Jinan Changsheng Machinery. Those who are interested in the two-component glue beater can pay attention to our http://linshi.jncsjx.com. Please look forward to more exciting content.