丁基胶涂布机遇到这些问题怎么处理?

时间:2023-01-23 来源:http://www.jncsjx.com/ 发布人:昌盛机械

丁基胶涂布机出现故障,可能会导致整个中空玻璃的进程停滞。而丁基胶涂布机是相对简单的中空玻璃设备,康捷机械为您介绍一下丁基胶涂布机的常见故障,以及遇到类似故障处理的方法。
The failure of butyl rubber coating machine may cause the process of the whole insulating glass to stop. Butyl rubber coating machine is a relatively simple insulating glass equipment. Kangjie Machinery will introduce you the common faults of butyl rubber coating machine and the methods for handling similar faults.
丁基胶涂布机挤出的丁基胶是毛刺不光滑时,如果是新设备,应先观察出胶孔是否光滑,如果出胶孔粗糙,应先打磨,再试机器;旧机器,可能显示的温度与实际的不相符,这时就需要将温度进行上调,直到出胶正常即可;
When the butyl adhesive extruded by the butyl adhesive coater is not smooth, if it is a new equipment, observe whether the glue hole is smooth. If the glue hole is rough, polish it first, and then try the machine again; For the old machine, the displayed temperature may not be consistent with the actual temperature. At this time, it is necessary to increase the temperature until the glue is discharged normally;
丁基胶涂布机打出的胶粘不到铝隔条上时,可能是原因还是温度过低,与胶要求的温度不太符合,只需要咨询丁基胶提供方需要的温度,将温度调整合适即可;

卧式丁基胶涂布机
When the adhesive produced by the butyl adhesive coater cannot reach the aluminum spacer strip, the most likely reason is that the temperature is too low, which is not in conformity with the temperature required by the adhesive. Just consult the butyl adhesive supplier for the required temperature and adjust the temperature properly;
丁基胶涂布机出现胶头漏胶,胶头下面是硅胶垫,估计是硅胶垫损坏导致的,只需要更换硅胶垫即可,但是,需要提醒的是,挤胶压力过大才是导致硅胶垫损坏的根本原因,不建议将挤胶压力调的过大;
The rubber head of the butyl rubber coating machine leaks, and the rubber head is under the silicone pad. It is estimated that the damage of the silicone pad is the cause. It is only necessary to replace the silicone pad. However, it should be reminded that the excessive extrusion pressure is the root cause of the damage of the silicone pad, and it is not recommended to adjust the extrusion pressure too much;
丁基胶涂布机的胶头或胶缸不加热,估计是加热棒损坏,更换即可;
The rubber head or rubber cylinder of the butyl rubber coater is not heated. It is estimated that the heating rod is damaged, and it can be replaced;
丁基胶涂布机的传送皮带跑偏,这个应该算不得故障,只需要调整四个角的皮带轮即可;
The conveyor belt of the butyl rubber coating machine deviates, which should not be considered as a fault. It only needs to adjust the pulley at four corners;
丁基胶涂布机的显示屏不亮,可以正常使用。这可能是显示屏损坏或者显示屏供电线出现问题,更换即可;
The display screen of butyl adhesive coater is not bright and can be used normally. This may be because the display screen is damaged or the power supply line of the display screen is faulty. Replace it;
本文由卧式丁基胶涂布机友情奉献.更多有关的知识请点击:http://linshi.jncsjx.com真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待
This article is dedicated by the horizontal butyl adhesive coater. For more information, please click: http://linshi.jncsjx.com Sincere attitude. We will provide you with comprehensive services. We will continue to offer you more relevant knowledge. Please look forward to it

联系我们Contact us

  • 咨询热线:0531-85717458 13705446998
  • 公司地址: 山东省德州市齐河安头乡企巢工业园
  • 扫码联系我们:

截屏,微信识别二维码

微信号:13705446998

//