一、丁基胶涂布机出胶正常，但涂不到铝框上
1、 The butyl adhesive coater is normal, but cannot be applied to the aluminum frame
(1) 胶头间隔过大，应调近间隔为0.5-0.6mm,如8.0铝框应调8.5-8.6。
(1) If the rubber head spacing is too large, the spacing should be adjusted to 0.5-0.6mm. For example, the 8.0 aluminum frame should be adjusted to 8.5-8.6.
(2)胶的熔点过高，提高胶头胶缸的温度。
(2) The melting point of the rubber is too high, which increases the temperature of the rubber cylinder of the rubber head.
二、丁基胶涂布机出胶量小
2、 The butyl rubber coater has small glue output
(1)查看系统的挤胶压力正常为8-16mPa。
(1) Check that the extrusion pressure of the system is normally 8-16mPa.
(2) 胶头被杂物阻塞，需整理胶头。用火油清洗作用更佳。
(2) The rubber head is blocked by sundries and needs to be sorted. It is better to clean with kerosene.
(3)丁基胶涂布机胶头不出胶
(3) Butyl rubber coating machine rubber head does not come out
(4)查看温度是否已达到设定温度。
(4) Check whether the temperature has reached the set temperature.
(5)查看系统是否有压力。
(5) Check the system for pressure.
气源压力0.4-0.6之间
Air supply pressure between 0.4-0.6

挤胶压力8-16之间
Extrusion pressure between 8-16
温度：依据胶的实际情况110-160之间，一般120℃
Temperature: according to the actual situation of rubber, between 110 and 160, generally 120 ℃
现用胶：胶缸为125℃ 胶头为125℃
Current rubber: 125 ℃ for rubber cylinder and 125 ℃ for rubber head
丁基胶涂布机铝框前段打不上胶：调整涂胶阀时刻，落下时刻减小。
The front section of the aluminum frame of the butyl adhesive coater cannot be glued: adjust the time of the gluing valve to reduce the falling time.
铝框后端打不上胶：调整涂胶阀时刻，抬起时刻加长。
The rear end of the aluminum frame can not be glued: adjust the time of the gluing valve and lengthen the lifting time.
SET选择 ENT承认 ? ?移位
SET Select ENT to acknowledge? displacement
丁基胶涂布机气液增压站的保护及修理
Protection and repair of gas-liquid booster station of butyl rubber coater
1、丁基胶涂布机系统翻开后，油缸无动作
1. After the butyl rubber coater system is turned over, the oil cylinder has no action
(1)查看外接气源是否正常。
(1) Check whether the external air source is normal.
(2)查看翻开液压电机开关后，系统电磁阀是否正常换向。
(2) Check whether the solenoid valve of the system reverses normally after turning on the hydraulic motor switch.
(3)减压阀是否已翻开。
(3) Whether the pressure reducing valve has been opened.
(4)查看气液增压站上的气管是否有气压。
(4) Check whether the gas pipe on the gas-liquid booster station has air pressure.
(5)如都正常，用平口螺丝刀按一下增压缸两头的小换向阀上的铜触头。
(5) If all are normal, press the copper contact on the small reversing valve at both ends of the booster cylinder with a flat-bladed screwdriver.
2、 丁基胶涂布机系统只进不退
2. Butyl adhesive coater system only moves forward but not backward
(1)胶缸操作退翻开时，看液压换向阀上的灯是否亮。
(1) Check whether the light on the hydraulic reversing valve is on when the rubber cylinder is operated and turned back.
(2)重复翻开关阀胶缸操作退开关，看是否能处理。
(2) Repeat the opening and closing valve rubber cylinder operation to check whether it can be handled.
(3)用铁片挡在液压换向阀的线圈端，灯亮时看是否有磁性，如无，需替换液压换向阀的伐圈，如有，需将换向阀拆下清洗。
(3) Block the coil end of the hydraulic reversing valve with an iron plate. When the light is on, check whether it is magnetic. If it is not, replace the valve ring of the hydraulic reversing valve. If it is, remove the reversing valve and clean it.
(4)液压换向阀被杂物卡住，需拆下清洗。
(4) The hydraulic reversing valve is stuck by sundries and needs to be removed for cleaning.
以上的精彩内容由卧式丁基胶涂布机进行推荐阅读，想要知道更多有用的知识，欢迎点击：http://linshi.jncsjx.com。
The above wonderful content is recommended for reading by the horizontal butyl adhesive coating machine. If you want to know more useful knowledge, please click: http://linshi.jncsjx.com 。