双组份打胶机操作

Two component gluing machine operation

1. 连接气源:

1. Connect the air source:

接通电源，调整减压阀至0.4 ~ 0.6MPa，检查系统是否漏气。然后试运行以下动作:(1)泵a举升;(2)泵a充电;(3)泵B举升;(4) B泵充电。注:升降升降油缸时，如果两个油缸不同步，请降低到原点，重新操作。

Connect the power supply, adjust the pressure reducing valve to 0.4~0.6MPa, and check if the system is leaking air. Then try the following actions: (1) Lift pump a; (2) Pump A charging; (3) Pump B lifting; (4) Pump B charging. Note: When lifting and lowering the oil cylinders, if the two cylinders are not synchronized, please lower them to the origin and operate again.

2. 将部件a、B的胶筒放到位，并对准橡胶泵a、B的轴线。

2. Place the rubber cylinders of components A and B in position and align them with the axis of rubber pumps A and B.

以A组件为例

Taking component A as an example

1)操作手动旋转阀将a泵提升至高水平，并观察提升过程中管路是否拉得过紧。

1) Operate the manual rotary valve to raise pump A to a high level and observe if the pipeline is pulled too tightly during the lifting process.

2)将胶筒置于a泵的压力板下，打开胶筒，将胶袋从胶筒中翻出来，取出胶面上的塑料片。

2) Place the rubber cylinder under the pressure plate of pump A, open the rubber cylinder, flip the rubber bag out of the cylinder, and remove the plastic sheet on the rubber surface.

3)使泵压盘缓慢下降。当压板进入枪管时，将其对准枪管开口。打开压力板的排气口，直到压力板接触橡胶表面。当压板内气体完全排出，有少量胶水从排气口溢出时，可关闭排气阀。(升降开关仍处于下压状态)

3) Slowly lower the pump pressure plate. When the pressure plate enters the barrel, align it with the opening of the barrel. Open the exhaust port of the pressure plate until it contacts the rubber surface. When the gas inside the pressure plate is completely discharged and a small amount of glue overflows from the exhaust port, the exhaust valve can be closed. (The lifting switch is still in the down pressed state)

4)开机试胶:打开主泵气源开关，按下胶枪开关，直到a泵内空气完全排出，胶从枪口连续排出。

4) Start up glue test: Turn on the main pump air source switch, press the glue gun switch, until the air in pump A is completely discharged, and the glue is continuously discharged from the gun mouth.

以同样的方式操作泵B。

Operate pump B in the same way.

3.上胶操作:

3. Gluing operation:

1)松开比例杠杆上比例泵的锁定螺钉，将比例泵的内外调节到所需比例。只有当胶水a和胶水B的比例达到正常值时，才能进行以下操作。

1) Loosen the locking screw of the proportional pump on the proportional lever and adjust the inside and outside of the proportional pump to the desired ratio. The following operations can only be carried out when the ratio of glue a to glue B reaches the normal value.

2) a和B泵设置选择旋钮,使喷胶枪的退出与中间缝的两块玻璃,打开开关喷胶枪,把胶枪顺利在适当的速度填充的双组分胶玻璃罐。上胶结束后，关闭胶枪。

2) Set the selection knobs for pumps A and B to allow the exit of the glue gun and the two pieces of glass in the middle seam. Turn on the switch of the glue gun and smoothly fill the two-component glue glass jar with the glue gun at an appropriate speed. After gluing, turn off the glue gun.

4. 更换胶筒:

4. Replace the rubber cylinder:

1)桶内胶水用完后，应立即关闭开关a、B，停止敲打。

1) After the glue in the bucket is used up, switches A and B should be immediately turned off and knocking should be stopped.

2)打开a(或b)橡胶泵的充气开关，选择a(或b)橡胶泵的升降机构作为上升位置，按下旋钮，使压板缓缓升起。这时要注意的是胶筒尽量不要离开底盘，待压板与胶筒完全分离后，关闭a(或b)胶泵的充气开关。

2) Turn on the inflation switch of the a (or b) rubber pump, select the lifting mechanism of the a (or b) rubber pump as the rising position, press the knob to slowly raise the pressure plate. At this point, it should be noted that the rubber cylinder should not leave the chassis as much as possible. After the pressure plate is completely separated from the rubber cylinder, turn off the inflation switch of the a (or b) rubber pump.

具体操作:关闭B泵，打开B回胶开关，然后打开胶枪，直到胶带变白。

Specific operation: Turn off pump B, turn on the B glue return switch, and then turn on the glue gun until the tape turns white.

本文由双组份打胶机友情奉献.更多有关的知识请点击:http://www.jncsjx.com真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is a friendly contribution from a two-component glue machine. For more information, please click: http://www.jncsjx.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned