The main factors affecting the quality of insulating glass equipment are the selection of raw materials and manufacturing process. The quality of these raw materials directly affects the quality and service life of hollow glass. At present, there are three main types of insulating glass in China: single-channel aluminum seal, double-channel aluminum seal and rubber strip composite seal. The aluminum channel single channel seal has been eliminated due to poor sealing and easy air intake, resulting in dew and frost on the glass and short service life.

当玻璃材料已知时，如普通玻璃或钢化玻璃，根据玻璃强度设计理论，可确定玻璃原片的断裂强度。因为中空玻璃机器生产的玻璃是由两片(或更多片)玻璃组成的，周边密封形成一个密封的气密层，当一面受载时，气密层上的玻璃变形并压缩中空层气体，气体压力增加，从而将部分载荷传递给另一面，所以在气体密封状态下，中空玻璃是两面玻璃共同承受载荷，两面玻璃同时发生变形。空心玻璃为双层或多层平板玻璃，由铝框用丁基胶和聚硫胶粘合而成，干燥剂注入其中。

When the glass material is known, such as ordinary glass or tempered glass, the breaking strength of the original glass sheet can be determined according to the glass strength design theory. Because the glass produced by the insulating glass machine is composed of two (or more) pieces of glass, and the surrounding sealing forms a sealed airtight layer. When one side is loaded, the glass on the airtight layer deforms and compresses the gas in the insulating layer, and the gas pressure increases, thus transferring part of the load to the other side. Therefore, in the gas sealing state, the insulating glass is both sides of the glass bear the load together, and both sides of the glass deform at the same time. Hollow glass is double-layer or multi-layer flat glass, which is made of aluminum frame bonded with butyl adhesive and polysulfide adhesive, and desiccant is injected into it.】、

生产中空玻璃设备的原玻璃有无色浮法玻璃、镀膜玻璃、钢化玻璃、夹层玻璃等。一般平板玻璃的透明度和强度都不能满足要求，应尽量避免使用普通平板玻璃。以上所述的玻璃原片必须符合相应的标准要求，并通过检验后才能使用。对不同生产厂家不同批次的玻璃，要检查是否有无色差现象，并将色差较大的玻璃分别用在不同工程或不同立面上。玻璃片的切削尺寸应严格按照图纸要求进行，同时操作者应注意玻璃的表面，不要有划痕，气泡等明显的缺陷。铝条插角的选择：铝条插角厚度应为0.30mm~0.35mm，且厚度均匀，透气孔分布均匀。铝条经阳极氧化或去污处理后，必须选择质量好、档次高的产品，以提高铝条的利用率。选择合适的角度尺寸，擦洗干净表面。

The raw glass for producing insulating glass equipment includes colorless float glass, coated glass, tempered glass, laminated glass, etc. The transparency and strength of general plate glass can not meet the requirements, and the use of ordinary plate glass should be avoided as much as possible. The original glass sheet mentioned above must meet the corresponding standard requirements and can be used only after passing the inspection. For different batches of glass from different manufacturers, first check whether there is color difference, and use the glass with large color difference on different projects or different facades. The cutting size of the glass sheet shall be in strict accordance with the requirements of the drawing. At the same time, the operator shall pay attention to the surface of the glass without obvious defects such as scratches and bubbles. Selection of aluminum strip insertion angle: the thickness of aluminum strip insertion angle should be 0.30 mm~0.35 mm, and the thickness should be uniform, and the distribution of air holes should be uniform. After anodizing or decontamination of aluminum strips, products with good quality and high grade must be selected to improve the utilization rate of aluminum strips. Select the appropriate angle size and scrub the surface.

空心玻璃设备的优点是节能环保，现代建筑的能耗主要是空调和照明，前者占55，后者占23，玻璃是建筑外墙中很薄、很易传热的材料。大多数玻璃厂所采用的中空玻璃生产线均为半自动板压或辊压生产设备，其生产节奏的快慢主要取决于板压速度和在线清洗的速度。若要提高一次交样成品率，就必须实行合片前各工序的自检和互检，从上片检验、铝框制作到丁基胶涂布等，特别要注意上框工序的质量检验，因为这一工序中基本上可以发现任何缺陷，而且合片前更容易纠正。

The advantage of hollow glass equipment is energy conservation and environmental protection. The energy consumption of modern buildings is mainly air conditioning and lighting, the former accounting for 55%, the latter accounting for 23%. Glass is a very thin and easy heat transfer material in the external walls of buildings. The insulating glass production lines used by most glass factories are semi-automatic plate-pressing or roll-pressing production equipment, and the speed of its production rhythm mainly depends on the plate-pressing speed and online cleaning speed. If we want to improve the yield of the first sample delivery, we must carry out self-inspection and mutual inspection of each process before lamination, from lamination inspection, aluminum frame fabrication to butyl rubber coating, etc., and pay special attention to the quality inspection of the framing process, because basically any defects can be found in this process, and it is easier to correct before lamination.

有了中空玻璃加工设备上面的小总结，希望对广大客户有所帮助，如果有什么不理解的或者寻求帮助的请点击我们的网站：http://www.jncsjx.com或者来电咨询，我们会尽全力为您解决

With the summary above of insulating glass processing equipment, I hope it can help our customers. If you have any questions or need help, please click our website: http://www.jncsjx.com Or call for consultation, and we will do our best to solve it for you