Failure of the butyl adhesive coating machine may cause the entire process of insulating glass to stall. The butyl adhesive coating machine is a relatively simple insulating glass equipment. Kangjie Machinery will introduce you to the common faults of the butyl adhesive coating machine and the methods for handling similar faults.

丁基胶涂布机挤出的丁基胶是毛刺不光滑时，如果是新设备，应先观察出胶孔是否光滑，如果出胶孔粗糙，应先打磨，再试机器；旧机器，可能显示的温度与实际的不相符，这时就需要将温度进行上调，直到出胶正常即可；

When the butyl adhesive extruded by the butyl adhesive coating machine has uneven burrs, if it is a new device, first observe whether the adhesive hole is smooth. If the adhesive hole is rough, first polish it and then try the machine again; For old machines, the displayed temperature may not match the actual temperature, so it is necessary to increase the temperature until the glue is released normally;

丁基胶涂布机打出的胶粘不到铝隔条上时，可能是原因还是温度过低，与胶要求的温度不太符合，只需要咨询丁基胶提供方需要的温度，将温度调整合适即可；

 

When the adhesive produced by the butyl adhesive applicator fails to adhere to the aluminum spacer strip, the most likely reason is that the temperature is too low, which does not meet the required temperature for the adhesive. Simply consult the butyl adhesive supplier for the required temperature and adjust the temperature appropriately;

丁基胶涂布机出现胶头漏胶，胶头下面是硅胶垫，估计是硅胶垫损坏导致的，只需要更换硅胶垫即可，但是，需要提醒的是，挤胶压力过大才是导致硅胶垫损坏的根本原因，不建议将挤胶压力调的过大；

The butyl adhesive applicator has a leakage of adhesive from the adhesive head, and there is a silicone pad underneath the adhesive head. It is estimated that the silicone pad is damaged, and it is only necessary to replace the silicone pad. However, it should be noted that excessive extrusion pressure is the root cause of damage to the silicone pad, and it is not recommended to adjust the extrusion pressure too high;

丁基胶涂布机的胶头或胶缸不加热，估计是加热棒损坏，更换即可；

The rubber head or rubber cylinder of the butyl adhesive coating machine is not heated, and it is estimated that the heating rod is damaged. Replace it;

丁基胶涂布机的传送皮带跑偏，这个应该算不得故障，只需要调整四个角的皮带轮即可；

The conveyor belt of the butyl adhesive coating machine deviates, which should not be considered a fault. It only needs to adjust the pulley at four corners;

丁基胶涂布机的显示屏不亮，可以正常使用。这可能是显示屏损坏或者显示屏供电线出现问题，更换即可；

The display screen of the butyl adhesive coating machine is not bright and can be used normally. This may be due to damage to the display screen or a problem with the display power supply line, which can be replaced;

本文由卧式丁基胶涂布机整理发布，您是不是对这些内容有所了解了呢?更多的内容请点击：http://www.jncsjx.com我们会有更多精彩内容等你查看。

This article is organized and released by a horizontal butyl adhesive coating machine. Do you have any understanding of these contents? For more information, please click: http://www.jncsjx.com We will have more exciting content waiting for you to check.