自动化双组份打胶机的工作原理
时间:2017-09-18 来源:http://www.jncsjx.com/ 发布人:昌盛机械
一、双组份打胶机如何正确使用
First, how to use the two component press?
1、在次使用新买的打胶机设备时,要注意检查设备是否完好无损、有无松动脱落现象。因为打胶机在运输过程中很可能因受到各种震动而使得机器设备上的各连接处有松动或者脱落,这就需要在检查完确认没问题过后才能投入使用。如果出现问题,应及时给予解决方可投入使用。
1, in the first use of new equipment to buy glue machine, we should pay attention to check whether the equipment is intact, whether or not loose and fall phenomenon. Because the rubber machine in the transportation process is likely to be caused by a variety of vibration and make the machinery and equipment on each of the connections are loose or fall off, this need to check after the confirmation of no problem, can be put into use. If any problems arise, they should be resolved in time before they can be put into use.
2、在打胶机的使用过程中,要注意不要用手去触摸该设备上的任何部位,不要去触摸控制箱内电路板上的元件,尤其禁止带电插拨,情节严重则会导致人身触电和损坏设备。
2, in the process of using glue machine, should pay attention to use the hand to touch any part of the equipment not, don't touch the control box on the circuit board components, specifically prohibited charged plug if the circumstances are serious, it will lead to electric shock and the damage of equipment.
3、操作人员应经常检查打胶机设备上的气管、胶管,防止这些管子老化破裂、漏气,避免这些问题可以增加安全。
3, operators should always check the rubber machine equipment on the trachea, hose, to prevent the aging of these tubes, rupture, leakage, and avoid these problems can increase safety.
4、在维修双组份打胶机时,不要随意更改该设备的开关、电机、电容等电气部件的规格,否则很可能导致该设备不能再投入使用。
4, in the maintenance of two component punch machine, do not arbitrarily change the device's switch, motor, capacitor and other electrical components specifications, otherwise it is likely to lead to the device can no longer be put into use.
双组份打胶机是从人工到自动化的一个重大转变。它包含了机械、电气、PLC程序的编写等。很好地诠释了机电一体化技术的非凡应用。是机电一体化朝着智能化、模块化、绿色化的佳体现。
A two component punch machine is a major shift from manual to automated. It includes the mechanical, electrical, PLC programming and so on. Very good interpretation of the extraordinary application of Mechatronics technology. It is the best embodiment of electromechanical integration towards intelligent, modular and green.
二、工作原理:压缩空气送入胶瓶(注射器),将胶压进与活塞室相连的进给管中,当活塞处于上冲程时,活塞室中填满胶,当活塞向下推进滴胶针头时,胶从针嘴压出。滴出的胶量由活塞下冲的距离决定,可以手工调节,也可以在软件中控制。
Two, the working principle of compressed air into the plastic bottle (injector), the rubber pressure into the piston chamber is connected with the feed tube, when the piston is in the up stroke, the piston chamber filled with glue, glue when the piston pushes down the needle, needle from the mouth out of glue. Glue drop out is determined by the distance of the piston down, can be manually adjusted, can also control the software.
2、特点:高速度、对胶剂粘度的低灵敏度。
2 features: high speed, low sensitivity to the viscosity of the adhesive.
3、优势:可提高点胶速度,改善点胶环境,提高点胶质量。通过利用气压和以微处理器为基础的定时装置来调节涂敷到部件上的流体量,替代了操作员的人为猜测。
3, advantages: can improve the dispensing speed, improve dispensing environment, improve dispensing quality. By using pneumatic and microprocessor based timing devices to adjust the amount of fluid applied to the components, the operator's artificial guesses are replaced.
本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站:http://www.jncsjx.com/谢谢您的到
The highlight of this article comes from a two piece dispenser. Please click on our official website: http://www.jncsjx.com/, thank you for coming
- 中空玻璃生产线一天能做多少平方 2024/12/23
- 全自动丁基胶涂布机操作规程 2024/12/14
- 丁基胶涂布机在使用的常见问题 2024/12/13
- 双组份打胶机如何调整滴胶量? 2024/12/09
- 中空玻璃生产线的磨损如何解决 2024/12/07
- 双组份打胶机对于打胶工作完成很重要 2024/12/05
- 全自动封胶线的工业自动化设备介绍 2024/12/03
- 玻璃涂布机设备:设备存在的安全隐患 2024/11/25
- 中空玻璃加工设备:玻璃开胶的应急处理措施 2024/11/21
- 中空玻璃生产线:玻璃起雾怎么办?昌盛为您解决! 2024/11/20