If bubbles appear during the operation of the glue machine, there must be some problems that cannot continue to work at this time, but these problems should be solved first, otherwise excessive bubbles will affect the production quality of the product. When the dual component glue filling machine is running, there are more reasons for producing bubbles. Then, as an operator, we should analyze and see what causes the foam, and then solve these problems. Today, let's briefly introduce the causes and solutions of foam.

如果使用双组分胶水灌装机时产生气泡，您可以考虑是否将气泡带入操作过程。例如，在混合时，如果只在一个方向搅拌，很容易导致混合不均匀，并且可能会有气泡。所以这是由混合不良引起的。这会减少气泡的影响。

If bubbles are generated when using a two component glue filling machine, you can consider whether to bring the bubbles into the operation process. For example, when mixing, stirring in only one direction can easily lead to uneven mixing and the possibility of bubbles. So this is caused by poor mixing. This will reduce the impact of bubbles.

此外，可能存在产生气泡的情况，即有一些需要使用气压的胶水灌装机。如果气压合理，例如漏气，此时可能会爆出气泡。在这种情况下，需要检查燃气管道，如果管道出现问题，则需要修理或更换。其次是温度，这也可能导致气泡。某些类型的胶水需要在一定的温度范围内使用。如果它不在这个温度范围内，它可能会让一些空气进入。

In addition, there may be situations where bubbles are generated, such as some glue filling machines that require the use of air pressure. If the air pressure is reasonable, such as a leak, bubbles may burst at this time. In this case, it is necessary to inspect the gas pipeline, and if there is a problem with the pipeline, it needs to be repaired or replaced. Next is temperature, which may also cause bubbles. Some types of glue need to be used within a certain temperature range. If it is not within this temperature range, it may allow some air to enter.

简单介绍双组分胶水机产生气泡的原因及解决方法。由于不同的原因，不同类型的胶水可能会产生气泡。例如，一些胶水可能粘度过大，内部气体无法正常排出。因此，需要使用一些化学试剂来减少几年的涂层，然后投入使用，这样才能有效地避免气泡。

Briefly introduce the causes and solutions of bubbles generated by the dual component glue machine. Due to different reasons, different types of glue may produce bubbles. For example, some adhesives may have excessive viscosity and internal gases cannot be discharged properly. Therefore, it is necessary to use some chemical reagents to reduce the coating for several years before putting it into use, in order to effectively avoid bubbles.

当我们在胶水操作中遇到气泡时，我们应该停下来分析气泡的根本原因，并注意在日常工作中积累一些经验。然后，随着时间的使用越来越长，我们可以通过经验找到处理这种情况的好方法。例如，在填充胶时，我们经常使用树脂，树脂通常会在填充胶的时候添加固化剂，但如果固化剂的比例出现问题，很可能会导致内部产生气泡。

When we encounter bubbles during glue operation, we should stop to analyze the root cause of the bubbles and pay attention to accumulating some experience in daily work. Then, as time goes by, we can find good ways to handle this situation through experience. For example, when filling the adhesive, we often use resin, and the resin usually adds a curing agent when filling the adhesive. However, if there is a problem with the proportion of the curing agent, it is likely to cause internal bubbles to form.