功能特点:
Features:
气动双组份打胶机是目前技术较好的中空玻璃密封胶打胶机。泵组件a和泵组件B分别由气动系统驱动，采用无触点电气控制系统控制。换向方向灵敏可靠。其独特的方便可调配比机构，很大限度保证了双组份胶的严格配比要求，出胶连续均匀，上胶效果好，生产效率高。
Pneumatic two-component sealant applicator is a kind of insulating glass sealant applicator with better technology at home and abroad. Pump assembly a and pump assembly B are driven by pneumatic system respectively and controlled by contactless electrical control system. The reversing direction is sensitive and reliable. Its unique convenient and adjustable proportioning mechanism greatly ensures the strict proportioning requirements of the two-component glue, continuous and uniform glue output, good gluing effect and high production efficiency.
双组份打胶机的操作
Operation of two-component sealant applicator
1. 连接气源:
1. Connect the air source:
接通电源，调节减压阀至0.4 ~ 0.6MPa，检查系统有无漏气。然后试运行以下动作:(1)泵举升(2)a泵充气(3)B泵举升(4)B泵充注。注:升降油缸升降时，若两个油缸不同步，请降至原点重新操作。
Connect the power supply, adjust the pressure reducing valve to 0.4~0.6MPa, and check the system for air leakage. Then try the following actions: (1) pump lifting (2) a pump charging (3) B pump lifting (4) B pump charging. Note: When lifting the lifting cylinder, if the two cylinders are not synchronized, please lower to the original point and operate again.

2. 将部件a、B的胶筒放到位，并与橡胶泵a、B的轴线对齐。
2. Place the rubber cylinders of parts a and B in place and align them with the axes of rubber pumps a and B.
以A组分为例
Take component A as an example
1)操作手动转阀将a泵举升到较高的气动双组份点胶机，观察举升过程中管路拉伸是否过紧。
1) Operate the manual rotary valve to lift pump a to a higher pneumatic two-component dispenser, and observe whether the pipeline tension is too tight during lifting.
2)将胶桶置于a泵压板下，打开双组份胶桶附件，将胶袋从桶内翻出，取出胶面塑料片。
2) Place the plastic bucket under the pressure plate of pump a, open the two-component plastic bucket accessory, turn the plastic bag out of the bucket, and take out the plastic sheet on the plastic surface.
3)使泵的压板缓慢下降。压力板进入筒体时，应与筒体开口对准。打开压板的排气口，直至压板与橡胶表面接触。当压板内气体完全排出，排气口有少量胶水溢出时，排气阀可关闭(升降开关仍处于下压状态)
3) Slowly lower the pressure plate of the pump. When the pressure plate enters the cylinder, it should be aligned with the cylinder opening. Open the air outlet of the pressure plate until the pressure plate contacts the rubber surface. When the gas in the pressure plate is completely discharged and a small amount of glue overflows from the exhaust port, the exhaust valve can be closed (the lifting switch is still in the downward pressure state)
4)开机试胶:打开主泵气源开关，按胶枪开关，直至泵a内空气完全排出，胶口不断排出。
4) Start up and test the glue: turn on the air source switch of the main pump and press the glue gun switch until the air in pump a is completely discharged and the glue mouth is continuously discharged.
用同样的方法操作泵B。
Operate pump B in the same way.
4. 上胶操作:
4. Gluing operation:
1)松开比例杆上比例泵的锁紧螺杆，将比例泵的内外调节到所需比例。只有当胶水a和胶水B的比例达到正常值时，才能进行以下操作。
1) Loosen the locking screw of the proportional pump on the proportional rod, and adjust the inside and outside of the proportional pump to the required proportion. The following operations can only be carried out when the ratio of glue a and glue B reaches the normal value.
2) a和B泵设置选择旋钮,使喷胶枪的退出与中间缝的两块玻璃,打开开关喷胶枪,把胶枪顺利在适当的速度填充的双组分胶玻璃罐。涂胶结束时关闭胶枪。
2) Set the selection knob for pumps a and B to make the exit of the glue gun and the two pieces of glass in the middle seam. Turn on the glue gun and fill the two-component glue glass tank with the glue gun at a proper speed. Close the glue gun at the end of gluing.
5. 更换胶筒:
5. Replace the rubber cartridge:
1)当桶内胶水用完时，应立即关闭a、B开关，停止轻敲。
1) When the glue in the bucket is used up, immediately turn off the a and B switches and stop tapping.
2)打开a(或b)橡胶泵的充气开关，将a(或b)橡胶泵的升降机构选为上升位置，按下旋钮，使压力板缓慢升降。此时要注意的是胶筒尽量不要离开底盘，待压板与胶筒完全分离后，关闭a(或b)胶泵的充气开关。3)取出空桶，将新的胶桶放在工作位置，重复第3、4、4项的操作。
2) Turn on the inflation switch of a (or b) rubber pump, select the lifting mechanism of a (or b) rubber pump as the rising position, and press the knob to make the pressure plate rise and fall slowly. At this time, it should be noted that the rubber cylinder should not leave the chassis as far as possible. After the pressing plate is completely separated from the rubber cylinder, turn off the inflation switch of a (or b) rubber pump. 3) Take out the empty bucket, put the new rubber bucket in the working position, and repeat the operations of items 3, 4 and 4.
1. 胶枪:由于双组份胶水是由两种胶水混合而成，其凝固速度与环境温度及a、B胶水的配比有关，混合后的胶水在20分钟内反应固化。因此，设备在正常上胶时，如果20分钟内未使用，就要把混好的胶洗掉，以免堵塞混胶机和胶枪。具体操作:关闭B泵，打开B回胶开关，再打开胶枪，直到胶条变白为止。
1. Glue gun: since the two-component glue is made of two kinds of glue, its solidification speed is related to the ambient temperature and the ratio of a and B glue. The mixed glue will react and solidify within 20 minutes. Therefore, if the equipment is not used within 20 minutes during normal gluing, the mixed glue should be washed away to avoid blocking the glue mixer and glue gun. Specific operation: turn off pump B, turn on the glue return switch of B, and then turn on the glue gun until the glue strip turns white.
枪清洗:
Gun cleaning:
用水烧制混合器，直至取出混合器芯;黑色把手上有个结。混合器与枪头之间的转动部分不得被烧;不要烧枪头。你可以用电线穿过去
Burn the mixer with water until the mixer core is taken out; There is a knot on the black handle. The rotating part between the mixer and the gun head shall not be burnt; Don't burn the gun head. You can wire it through
以上就是为大家介绍的有关双组份打胶机详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.jncsjx.com
The above is a detailed introduction to the two-component sealant applicator for you. I hope it can help you. If you have any questions, please contact us. We will provide you with our service http://www.jncsjx.com