涂布机涂布前，将清洁的，绷好网的网版从涂布机前面装入，有的机型也可从侧面装入网版。在为大幅面网框设计的机型中，侧面装版更为常见，因为网框大且笨重，侧面装版，可使抬升量和搬动量小一些。在自动丝网涂布机与其他自动丝网处理设备（如清洁设备、再*设备、干燥装置和显影机）联机运行时，从侧面装版更为便利。
Before coating, load the clean and stretched screen from the front of the coater, and some models can also load the screen from the side. In the models designed for large format mesh frames, side mounting is more common, because the mesh frames are large and bulky. Side mounting can reduce the lifting and moving amount. When the automatic screen coater is running online with other automatic screen processing equipment (such as cleaning equipment, re * equipment, drying device and developer), it is more convenient to install the plate from the side.
涂布机的开机程序：
Startup procedure of coater:
1、合上总电源开关及控制柜上电源开关；
1. Close the main power switch and the power switch on the control cabinet;
2、在张力控制器上设定好初始值（一般为180~280）及分频数（通常为20~50）；
2. Set the initial value (generally 180 ~ 280) and frequency division number (usually 20 ~ 50) on the tension controller;
3、设定涂布工作方式和相关参数（涂布速度、段长、间隙长度、辊速比等），而后接通压缩空气（调节气动控制箱调压阀使气动压力在0.2~0.3Mpa之间）；
3. Set the coating working mode and relevant parameters (coating speed, section length, gap length, roll speed ratio, etc.), and then connect the compressed air (adjust the pressure regulating valve of the pneumatic control box to make the pneumatic pressure between 0.2 ~ 0.3MPa);
4、启动干燥风机和干燥温控仪；
4. Start the drying fan and drying temperature controller;
5、接通自动纠偏和张力控制器电源；
5. Turn on the power supply of automatic deviation correction and tension controller;
6、设备各段温度均已达到工艺要求温度；
6. The temperature of each section of the equipment has reached the temperature required by the process;
7、给涂布装置料斗加料，同时启动涂布机，进行涂布。
7. Feed the hopper of the coating device and start the coater for coating at the same time.
维持涂布机的正常运行，要按照涂布机操作规程进行：
To maintain the normal operation of the coater, it is necessary to follow the operating procedures of the coater:

涂布机的开机前准备：
Preparation before startup of coater:
1、检查各电气开关，联线有无脱落或破损等异常现象；
1. Check whether all electrical switches and connecting wires fall off or are damaged;
2、按工艺片路要求在常温停机状态下穿好牵引带；
2. Put on the traction belt under normal temperature shutdown according to the process requirements;
3、启动排风设备；
3. Start the exhaust equipment;
4、确认在涂布机房内无任何明火（如电炉等）；
4. Confirm that there is no open fire in the coating machine room (such as electric furnace);
5、涂布机控制柜和干燥箱体外壳可靠接地。
5. The control cabinet of the coater and the shell of the drying box are reliably grounded.
本文的精彩内容由卧式丁基胶涂布机提供知识提供，本网站还有很多的精彩内容，更多的内容您可以点击进入：http://linshi.jncsjx.com/我们有专门的客服为您解答问题
The wonderful content of this article is provided by the horizontal butyl rubber coater. There are many wonderful contents on this website. You can click to enter more contents: http://linshi.jncsjx.com/ We have special customer service to answer your questions